MCP6S26-I/P
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 6.4kOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Other Analog ICs |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT APPLICABLE |
| Number of Functions | 1 |
| Supply Voltage | 4V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | NOT APPLICABLE |
| Base Part Number | MCP6S26 |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Output Type | Push-Pull, Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Number of Circuits | 6 |
| Analog IC - Other Type | ANALOG CIRCUIT |
| Operating Supply Current | 1mA |
| Nominal Supply Current | 1mA |
| Slew Rate | 22V/μs |
| Amplifier Type | Programmable Gain |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 275μV |
| Bandwidth | 12MHz |
| Voltage Gain | 30.1dB |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Voltage - Input Offset | 275μV |
| Height | 3.3mm |
| Length | 19.05mm |
| Width | 6.35mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
MCP6S26-I/P Overview
A 14-DIP (0.300, 7.62mm) case is used to package the op amp. Programmable Gain-type instrumentation amplifiers are used in this application. A Tube case is used for delivering the op amp. The number of terminations approaches 14. There are a total of 14 pins on this op amp. It would be helpful if you could remember that this op amp ic should be powered by an 4V battery. This particular linear amplifier is a type of Other Analog ICs device, to be precise. In total, the buffer amplifier consists of 14 pins. As far as the input offset voltage is concerned, linear amplifier rates at 275μV. This electronic component is recommended to be mounted using the mounting type Through Hole. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~85°C . In order for this instrumentation amplifier to operate, the supply current needs to be between 1mA and 10 . Op amp is a member of the 30.1dB's 30.1dB family. The buffer amp consists of 6 circuits in total. On the output type, there are Push-Pull, Rail-to-Rail different types of op amps. 1 elements make up the design of this buffer amplifier. The operating supply voltage of instrumentation amplifier is rated 5V voltage. 6.4kOhm is the range in which the instrumentation amplifier resistance should lie. Besides the analog ICs used in this instrumentation amplifier, there is also another type of analog IC called ANALOG CIRCUIT IC.
MCP6S26-I/P Features
14 Pins
supply voltage of 4V
30.1dB voltage gain
Output Type: Push-Pull, Rail-to-Rail
Resistance of 6.4kOhm
MCP6S26-I/P Applications
There are a lot of Microchip Technology MCP6S26-I/P Instrumentational OP Amps applications.
- ECG equipment
- MP3
- Radar
- Comparator
- Power transmission
- Blood pressure sensors
- Switching amplifier
- Weak signal detection
- Tablets
- Scintillation detectors
