MCP6S28-I/P
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 6.4kOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Other Analog ICs |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 4V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MCP6S28 |
| Pin Count | 16 |
| Output Type | Push-Pull, Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Number of Circuits | 8 |
| Analog IC - Other Type | ANALOG CIRCUIT |
| Operating Supply Current | 1mA |
| Nominal Supply Current | 4mA |
| Slew Rate | 22V/μs |
| Amplifier Type | Programmable Gain |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 275μV |
| Bandwidth | 12MHz |
| Voltage Gain | 30.1dB |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Voltage - Input Offset | 275μV |
| Height | 3.68mm |
| Length | 19.3mm |
| Width | 6.6mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6S28-I/P Overview
Packaging for the buffer amplifier is in the form of a 16-DIP (0.300, 7.62mm) case. Buffer amps of this type are called Programmable Gain-types. In the case of Tube cases, linear amplifier will be delivered. A total of 16 terminations have been reported in the past few weeks. The total number of pins on linear amplifier is 16. Please take in mind that this instrumentation amplifier should be run at 4V. In more specific terms, this linear amplifier can be categoriOther Analog ICsed as a Other Analog ICs-type device. 16 pins are available on the instrumentation amplifier. With regards to the offset voltage of the input, buffer amplifier is rated at 275μV. The mounting type that is recommended for this electrical part is Through Hole. With regard to operating temperature, this op amp functions well at -40°C~85°C. You can run this op amp ic on 1mA . It is recommended to keep the voltage gain at 30.1dB at all times. There are 8 circuits on op amps. There are a total of 1 channels available on the op amps. In addition to outputting Push-Pull, Rail-to-Rail signals, this op amp ic offers a number of other advantages. The operating supply voltage of instrumentation amplifier is rated 5V voltage. It is important to keep the resistance within the 6.4kOhm range of the op amps. The buffer op amp also uses a ANALOG CIRCUIT analog IC.
MCP6S28-I/P Features
16 Pins
supply voltage of 4V
30.1dB voltage gain
Output Type: Push-Pull, Rail-to-Rail
Resistance of 6.4kOhm
MCP6S28-I/P Applications
There are a lot of Microchip Technology MCP6S28-I/P Instrumentational OP Amps applications.
- Medical imaging
- Fission chambers
- Mobile phone
- Measurements of Wheatstone bridge
- Tablets
- Fast A/D and D/A converters
- Inverse/same-phase proportional circuit
- High speed sample
- Information processing
- Test and measurement instruments
