MCP6S91T-E/SN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 10 TΩ |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Other Analog ICs |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6S91 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Analog IC - Other Type | ANALOG CIRCUIT |
| Operating Supply Current | 1mA |
| Nominal Supply Current | 1.6mA |
| Slew Rate | 22V/μs |
| Amplifier Type | Programmable Gain |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Output Current per Channel | 25mA |
| Input Offset Voltage (Vos) | 4mV |
| Bandwidth | 18MHz |
| Gain Bandwidth Product | 18MHz |
| Voltage Gain | 30.1dB |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Voltage - Input Offset | 400μV |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6S91T-E/SN Overview
In the package, you will find a 8-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. The instrumentation amplifier in this picture is of the Programmable Gain-type. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. It is estimated that there will be 8 terminations in the next few months. The pins on this board total to 8 in total. I would like to remind you that this buffer op amp should be powered by an 5V battery. To be specific, this instrumentation amplifier is a type of Other Analog ICs. The buffer op amp includes 8 pins. In terms of the input offset voltage, instrumentation amplifier rates at 4mV. Surface Mount is the recommended mounting type of operational amplifiers. With regard to operating temperature, op amp ranges -40°C~125°C. An 1mA volt supply current is needed for this linear amplifier to operate. Voltage gain should remain at 30.1dB. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. A voltage rating of 1 is indicated for the op amp's operating supply voltage. The operating supply voltage of the buffer op amp is rated at 5V. In order for the buffer amplifier resistance to remain within the 10 TΩ range, the device should be tested. An analog IC known as ANALOG CIRCUIT is also used in this linear amplifier.
MCP6S91T-E/SN Features
8 Pins
supply voltage of 5V
30.1dB voltage gain
Output Type: Rail-to-Rail
Resistance of 10 TΩ
MCP6S91T-E/SN Applications
There are a lot of Microchip Technology MCP6S91T-E/SN Instrumentational OP Amps applications.
- earphone
- Polarized electrodes
- High input resistance broadband
- Hand-held batteries
- Television broadcasting equipment
- Home audio systems
- Logarithmic operation circuits
- Power transmission
- Computer workstations
- High speed sample
