MCP6S92T-E/MS
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 10 TΩ |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Other Analog ICs |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6S92 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Analog IC - Other Type | ANALOG CIRCUIT |
| Nominal Supply Current | 1.6mA |
| Current - Supply | 1mA |
| Slew Rate | 22V/μs |
| Amplifier Type | Programmable Gain |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Input Offset Voltage (Vos) | 4mV |
| Bandwidth | 18MHz |
| Gain Bandwidth Product | 18MHz |
| Voltage Gain | 30.1dB |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Voltage - Input Offset | 400μV |
| Current - Output / Channel | 25mA |
| Length | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6S92T-E/MS Overview
Packaging for the buffer amplifier is in the form of a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case. Buffer amps of this type are called Programmable Gain-types. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. There is a growing number of terminations approaching the number of 8. The total number of pins on linear amplifier is 8. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. There are two types of Other Analog ICs op amps in this case, and this device falls into one of them. An 8-pin op amp ic is included in the package. The input offset voltage is 4mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. Keeping the voltage gain at 30.1dB is the best course of action. A linear amplifier like this has 2 circuits on it. On the buffer amps, there are 1 channels that can be used. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. The operating supply voltage of instrumentation amplifier is rated 5V voltage. We recommend that you use this electronic part with an 1mA supply in order to get the best performance from it. Instrumentation amplifier resistance should remain within the range of 10 TΩ. The other type of analog IC used in this op amp ic is known as ANALOG CIRCUIT.
MCP6S92T-E/MS Features
8 Pins
supply voltage of 5V
30.1dB voltage gain
Output Type: Rail-to-Rail
Resistance of 10 TΩ
MCP6S92T-E/MS Applications
There are a lot of Microchip Technology MCP6S92T-E/MS Instrumentational OP Amps applications.
- Weighing systems
- Instrumentation
- Thermocouples
- Fission chambers
- Tablets
- Industrial control system
- Comparator
- Power generator
- RF cable systems
- Division circuits
