MCP6V01-E/SN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6V01 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Power Supplies | 2/5V |
| Number of Channels | 1 |
| Operating Supply Current | 300μA |
| Nominal Supply Current | 300μA |
| Output Current | 22mA |
| Slew Rate | 0.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 130 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V |
| Output Current per Channel | 22mA |
| Input Offset Voltage (Vos) | 2μV |
| Bandwidth | 1.3MHz |
| Unity Gain BW-Nom | 1300 kHz |
| Voltage Gain | 156dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 130dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6.5V |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height | 1.2446mm |
| Length | 4.8768mm |
| Width | 3.9116mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6V01-E/SN Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. A Zero-Drift-type buffer amplifier is shown here. Linear amplifier is delivered in a Tube case. It is estimated that there will be 8 terminations in the next few months. A total of 8 pins are located on this board. I would like to remind you that this buffer op amp should be powered by an 1.8V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. The op amp ic has an array of 8 pins on it. With regard to input offset voltage, instrumentation amplifier is rated at 2μV. This electronic part is best mounted with type Surface Mount. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~125°C . You can run this op amp ic on 300μA . Maintain 156dB as the voltage gain. The op amp ic has 1 channels on it. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer.
MCP6V01-E/SN Features
8 Pins
supply voltage of 1.8V
156dB voltage gain
Output Type: Rail-to-Rail
MCP6V01-E/SN Applications
There are a lot of Microchip Technology MCP6V01-E/SN Instrumentational OP Amps applications.
- Professional videography
- Test and measurement instruments
- RF cable systems
- Comparator
- Polarized electrodes
- MP3
- Multimedia playback equipment
- Biopotential
- Logarithmic operation circuits
- PDA
