MCP6V01T-E/SN
| Parameters | |
|---|---|
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6V01 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 1 |
| Power Supplies | 2/5V |
| Nominal Supply Current | 300μA |
| Output Current | 22mA |
| Current - Supply | 300μA |
| Slew Rate | 0.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 130 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V |
| Input Offset Voltage (Vos) | 2μV |
| Gain Bandwidth Product | 1.3MHz |
| Unity Gain BW-Nom | 1300 kHz |
| Voltage Gain | 156dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 130dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6.5V |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Wideband | NO |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MCP6V01T-E/SN Overview
It is packaged in an 8-SOIC (0.154, 3.90mm Width)-case that protects the operational amplifiers from damage. A Zero-Drift-type buffer amplifier is shown here. Instrumentation amplifier is delivered in a Tape & Reel (TR) case. It is estimated that there will be 8 terminations in the next few months. The total number of pins on linear amplifier is 8. It is important to remember that this op amp should be operated at a voltage of 1.8V volts. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. 8 pins are located on the operational amplifiers. In terms of input offset voltage, operational amplifier rates 2μV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. With regard to operating temperature, op amp ranges -40°C~125°C. The voltage gain should stay at 156dB. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. Depending on the chip's operating supply voltage, op amp ic has a rated voltage of 1. A TAPE AND REEL-shaped amplifier is used to pack the buffer amps. To run supply current of buffer amplifier under 300μA.
MCP6V01T-E/SN Features
8 Pins
supply voltage of 1.8V
156dB voltage gain
Output Type: Rail-to-Rail
MCP6V01T-E/SN Applications
There are a lot of Microchip Technology MCP6V01T-E/SN Instrumentational OP Amps applications.
- Proportional operation circuits
- Video conversion and routing
- RF cable systems
- Ultrasound transducers
- Computer workstations
- E-book readers
- Exponential operation circuits
- Video amplifiers
- Switching amplifier
- Biopotential
