MCP6V02-E/SN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 1.8V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6V02 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Channels | 2 |
| Operating Supply Current | 300μA |
| Nominal Supply Current | 300μA |
| Output Current | 22mA |
| Slew Rate | 0.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 130 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V |
| Output Current per Channel | 22mA |
| Input Offset Voltage (Vos) | 2μV |
| Bandwidth | 1.3MHz |
| Unity Gain BW-Nom | 1300 kHz |
| Voltage Gain | 156dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 130dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6.5V |
| Low-Bias | YES |
| Micropower | YES |
| Min Supply Voltage (DC) | 1.8V |
| Height | 1.25mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6V02-E/SN Overview
In the package, you will find a 8-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. An op amp ic of the Zero-Drift type. Linear amplifier is delivered in a Tube case. The number of terminations approaches 8. It consists of a total of 8 pins in total. Please take in mind that op amp should be run at 1.8V. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. It has 8 pins that make up the linear amplifier. In terms of the input offset voltage, instrumentation amplifier rates at 2μV. This electronic part is recommended for mounting type Surface Mount. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~125°C. A supply current of 300μA can be used to operate this linear amplifier. There should be no change in the voltage gain at 156dB. There are a total of 2 channels available on the op amps. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals.
MCP6V02-E/SN Features
8 Pins
supply voltage of 1.8V
156dB voltage gain
Output Type: Rail-to-Rail
MCP6V02-E/SN Applications
There are a lot of Microchip Technology MCP6V02-E/SN Instrumentational OP Amps applications.
- Inverse/same-phase proportional circuit
- Switching amplifier
- Mobile phone
- Tablets
- Proportional operation circuits
- Fission chambers
- High-frequency data acquisition systems
- pH (acidity)
- Multiplication circuits
- Division circuits
