MCP6V03T-E/MNY
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-WFDFN Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2000 |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5.5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6V03 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Power Supplies | 2/5V |
| Number of Channels | 1 |
| Nominal Supply Current | 300μA |
| Output Current | 22mA |
| Current - Supply | 300μA |
| Slew Rate | 0.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 130 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V |
| Input Offset Voltage (Vos) | 2μV |
| Bandwidth | 1.3MHz |
| Unity Gain BW-Nom | 1300 kHz |
| Voltage Gain | 156dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 130dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6.5V |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height | 750μm |
| Length | 2mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
MCP6V03T-E/MNY Overview
It is packaged in an 8-WFDFN Exposed Pad-case that protects the operational amplifiers from damage. This is a Zero-Drift type op amp. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. In recent months, the number of terminations has approached 8. It consists of a total of 8 pins in total. It would be helpful if you could remember that this op amp ic should be powered by an 5.5V battery. It should be noted that this op amp is a type of Operational Amplifier device. In total, the buffer amplifier consists of 8 pins. Op amp rates 2μV as input offset voltage. This electronic part is best mounted with type Surface Mount. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~125°C . It is recommended to keep the voltage gain at 156dB at all times. There are a total of 1 channels available on the op amps. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. An buffer amplifier is packed in a TAPE AND REEL-shape according to the design. To run supply current of buffer amplifier under 300μA.
MCP6V03T-E/MNY Features
8 Pins
supply voltage of 5.5V
156dB voltage gain
Output Type: Rail-to-Rail
MCP6V03T-E/MNY Applications
There are a lot of Microchip Technology MCP6V03T-E/MNY Instrumentational OP Amps applications.
- Commercial audio systems
- pH (acidity)
- Gaming industry
- Hand-held batteries
- Radiation thermometry transducers
- Test equipment
- Measurements of Wheatstone bridge
- Large motor controllers
- Inverse/same-phase proportional circuit
- RF cable systems
