MCP6V06T-E/MNY
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-WFDFN Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2000 |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5.5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6V06 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Current - Supply | 300μA |
| Slew Rate | 0.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 120 dB |
| Current - Input Bias | 6pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V |
| Input Offset Voltage (Vos) | 3μV |
| Bandwidth | 1.3MHz |
| Unity Gain BW-Nom | 1300 kHz |
| Voltage Gain | 158dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 125dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height | 750μm |
| Length | 2mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6V06T-E/MNY Overview
A 8-WFDFN Exposed Pad case is used to package the op amp. A Zero-Drift-type buffer amplifier is shown here. Linear amplifier is delivered in a Tape & Reel (TR) case. It is estimated that there will be at least 8 terminations this year. The total number of pins on linear amplifier is 8. It would be helpful if you could remember that this op amp ic should be powered by an 5.5V battery. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. There are 8 pins on this chip. Op amp ic rates 3μV for input offset voltage. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. Keeping the voltage gain at 158dB is the best course of action. A linear amplifier like this has 1 circuits on it. There are 1 channels on the operational amplifiers. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. The operating supply voltage of instrumentation amplifier is rated 5V voltage. For the packing of the instrumentation amplifier, TAPE AND REEL is adopted. To run supply current of buffer amplifier under 300μA.
MCP6V06T-E/MNY Features
8 Pins
supply voltage of 5.5V
158dB voltage gain
Output Type: Rail-to-Rail
MCP6V06T-E/MNY Applications
There are a lot of Microchip Technology MCP6V06T-E/MNY Instrumentational OP Amps applications.
- Portable electronic products powered by batteries
- Inverse/same-phase proportional circuit
- Biopotential
- Blood pressure sensors
- Vehicle electronics
- Power control
- Integrator circuits
- Video amplifiers
- High/low-pass filter circuit
- Differentiator circuits
