MCP6V11UT-E/LT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2003 |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6V11U |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Nominal Supply Current | 7.5μA |
| Output Current | 17mA |
| Current - Supply | 7.5μA |
| Slew Rate | 0.03V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 119 dB |
| Current - Input Bias | 5pA |
| Voltage - Supply, Single/Dual (±) | 1.6V~5.5V |
| Input Offset Voltage (Vos) | 8μV |
| Bandwidth | 80 kHz |
| Unity Gain BW-Nom | 80 kHz |
| Voltage Gain | 135dB |
| Power Supply Rejection Ratio (PSRR) | 118dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Current - Output / Channel | 17mA |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height | 1mm |
| Length | 2.25mm |
| Width | 1.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6V11UT-E/LT Overview
Op amp is packaged in 5-TSSOP, SC-70-5, SOT-353 case. This is a Zero-Drift type op amp. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. During the past two weeks, there have been close to 5 terminations. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 5 pins are located on the operational amplifiers. Regarding input offset voltage, buffer amplifier rates 8μV voltage. Surface Mount is the recommended mounting type of operational amplifiers. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . There should be no change in the voltage gain at 135dB. On the buffer amps, there are 1 channels that can be used. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. For the packing of the instrumentation amplifier, TAPE AND REEL is adopted. To run supply current of buffer amplifier under 7.5μA.
MCP6V11UT-E/LT Features
135dB voltage gain
Output Type: Rail-to-Rail
MCP6V11UT-E/LT Applications
There are a lot of Microchip Technology MCP6V11UT-E/LT Instrumentational OP Amps applications.
- Differentiator circuits
- High/low-pass filter circuit
- Car stereo
- Power generator
- Micro signal measurement
- Medical imaging
- Fast A/D and D/A converters
- pH (acidity)
- Proportional counter tubes
- RF cable systems
