MCP6V26-E/MS
| Parameters | |
|---|---|
| Subcategory | Operational Amplifiers |
| Packing Method | TRAY |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 2.3V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MCP6V26 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Power Supplies | 2.5/5V |
| Number of Channels | 1 |
| Nominal Supply Current | 620μA |
| Output Current | 22mA |
| Current - Supply | 620μA |
| Slew Rate | 1V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 120 dB |
| Current - Input Bias | 7pA |
| Voltage - Supply, Single/Dual (±) | 2.3V~5.5V |
| Input Offset Voltage (Vos) | 2μV |
| Bandwidth | 2MHz |
| Unity Gain BW-Nom | 2000 kHz |
| Voltage Gain | 155dB |
| Power Supply Rejection Ratio (PSRR) | 125dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6.5V |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height | 950μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2011 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
MCP6V26-E/MS Overview
There is a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case in which the instrumentation amplifier is packaged. Zero-Drift-type instrumentation amplifiers are used in this application. The op amp is delivered to you in a Tube case. We are approaching the 8h termination of the year. Buffer amplifier has a total of 8 pins on it. It would be helpful if you could remember that this op amp ic should be powered by an 2.3V battery. To be specific, this instrumentation amplifier is a type of Operational Amplifiers. The buffer op amp includes 8 pins. With regard to input offset voltage, instrumentation amplifier is rated at 2μV. This electronic component is recommended to be mounted using the mounting type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. Voltage gain should remain at 155dB. There are a total of 1 channels available on the op amps. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. It is used TRAY to pack the op amps. A supply of 620μA or higher is recommended for use with this electronic part.
MCP6V26-E/MS Features
8 Pins
supply voltage of 2.3V
155dB voltage gain
Output Type: Rail-to-Rail
MCP6V26-E/MS Applications
There are a lot of Microchip Technology MCP6V26-E/MS Instrumentational OP Amps applications.
- Portable media players
- Automotive sensors
- Computer workstations
- Displayers for aircraft and air transportation control systems
- Multiplication circuits
- Fission chambers
- Automatic control
- Test equipment
- Integrator circuits
- Comparator
