MCP6V27-E/MD
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-VDFN Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2011 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Subcategory | Operational Amplifiers |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 2 |
| Supply Voltage | 2.3V |
| Base Part Number | MCP6V27 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Channels | 2 |
| Operating Supply Current | 620μA |
| Nominal Supply Current | 620μA |
| Output Current | 22mA |
| Slew Rate | 1V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 120 dB |
| Current - Input Bias | 7pA |
| Voltage - Supply, Single/Dual (±) | 2.3V~5.5V |
| Output Current per Channel | 22mA |
| Input Offset Voltage (Vos) | 2μV |
| Bandwidth | 2MHz |
| Unity Gain BW-Nom | 2000 kHz |
| Voltage Gain | 155dB |
| Power Supply Rejection Ratio (PSRR) | 125dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6.5V |
| Low-Bias | YES |
| Micropower | YES |
| Height | 950μm |
| Length | 4mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6V27-E/MD Overview
There is a 8-VDFN Exposed Pad case in which the instrumentation amplifier is packaged. An op amp ic of the Zero-Drift type. Upon delivery, op amp ic is packaged in a Tube case. It is estimated that there will be 8 terminations in the next few months. In this case, there are 8 pins on the board. The linear amplifier should be run at 2.3V at all times, so please keep that in mind when using it. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifiers device. In total, the buffer amplifier consists of 8 pins. Regarding input offset voltage, op amp rates 2μV. This electrical part should be mounted using type Surface Mount. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~125°C . An 620μA volt supply current is needed for this linear amplifier to operate. 155dB should be the voltage gain. 2 channels are available on the instrumentation amplifier. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages.
MCP6V27-E/MD Features
8 Pins
supply voltage of 2.3V
155dB voltage gain
Output Type: Rail-to-Rail
MCP6V27-E/MD Applications
There are a lot of Microchip Technology MCP6V27-E/MD Instrumentational OP Amps applications.
- Vehicle electronics
- Automatic control
- Professional videography
- Power generator
- Semiconductor detectors
- Active probe
- Video conversion and routing
- Video computer boards
- Polarized electrodes
- Proportional operation circuits
