MCP6V28-E/SN
| Parameters | |
|---|---|
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Power Supplies | 2.5/5V |
| Number of Channels | 1 |
| Operating Supply Current | 620μA |
| Nominal Supply Current | 620μA |
| Output Current | 22mA |
| Slew Rate | 1V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 120 dB |
| Current - Input Bias | 7pA |
| Voltage - Supply, Single/Dual (±) | 2.3V~5.5V |
| Output Current per Channel | 22mA |
| Input Offset Voltage (Vos) | 2μV |
| Bandwidth | 2MHz |
| Unity Gain BW-Nom | 2000 kHz |
| Voltage Gain | 155dB |
| Power Supply Rejection Ratio (PSRR) | 125dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6.5V |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height | 1.25mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2011 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TRAY |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 2.3V |
| Base Part Number | MCP6V28 |
MCP6V28-E/SN Overview
Op amp is packaged in 8-SOIC (0.154, 3.90mm Width) case. An op amp ic of the Zero-Drift type. Linear amplifier is delivered in a Tube case. There is a growing number of terminations approaching the number of 8. Buffer amplifier has a total of 8 pins. It would be helpful if you could remember that this op amp ic should be powered by an 2.3V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. 8 pins are available on the instrumentation amplifier. The input offset voltage is 2μV. The mounting type that is recommended for this electrical part is Surface Mount. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. In order for this instrumentation amplifier to operate, the supply current needs to be between 620μA and 10 . The voltage gain should stay at 155dB. The op amp ic has 1 channels on it. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. For packing the buffer amplifier, the TRAY-axis is adopted.
MCP6V28-E/SN Features
8 Pins
supply voltage of 2.3V
155dB voltage gain
Output Type: Rail-to-Rail
MCP6V28-E/SN Applications
There are a lot of Microchip Technology MCP6V28-E/SN Instrumentational OP Amps applications.
- Gaming industry
- Proportional operation circuits
- Automotive sensors
- Vehicle electronics
- Biopotential
- Measurements of Wheatstone bridge
- Signal filtering
- Band-stop filter
- High/low-pass filter circuit
- Radar
