MIC2076-1YM
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e4 |
| Feature | Slew Rate Controlled, Status Flag |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 90mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Current Rating | 1.25A |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MIC2076 |
| Number of Outputs | 2 |
| Output Voltage | 6V |
| Output Type | N-Channel |
| Max Output Current | 500mA |
| Interface | On/Off |
| Nominal Supply Current | 5μA |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Turn On Delay Time | 5 μs |
| Switch Type | General Purpose |
| Min Input Voltage | 2.7V |
| Max Input Voltage | 5.5V |
| Nominal Input Voltage | 5.5V |
| Turn-Off Delay Time | 100 μs |
| Threshold Voltage | 2.7V |
| Ratio - Input:Output | 1:2 |
| Voltage - Load | 2.7V~5.5V |
| Fault Protection | Current Limiting (Fixed), Over Temperature, UVLO |
| Turn On Time | 5000 μs |
| Output Peak Current Limit-Nom | 0.9A |
| Rds On (Typ) | 90m Ω |
| Built-in Protections | OVER CURRENT; THERMAL; UNDER VOLTAGE |
| Output Current Flow Direction | SINK |
| Height | 1.63mm |
| Length | 5mm |
| Width | 3.99mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MIC2076-1YM Overview
Tube is the way it's packaged.The 8-SOIC (0.154, 3.90mm Width) package contains it.Surface Mount is the mounting type of the LED driver.General Purpose is the type of switch owned by it.It is recommended that the temperature be set to -40°C~85°C TA for reliable operation.There are 2 outputs available on this lighting driver.Operation is based on a supply voltage of Not Required.There is a maximum output voltage of N-Channel volts on this LED driver.In terms of features, the LED driving board has Slew Rate Controlled, Status Flag.The MIC2076 family consists of this type.It contains 8 terminations.The 8 pins are used to operate the LED driver.It is important to note that the LED driving board has 1 functions.To comply with the operation criteria, the maximum output current is reduced to 500mA.With a supply voltage of 5V, high efficiency is possible.Surface Mount is mounted in the way.Lighting drivers with 90mOhm resistance are used.Input voltage is limited to 5.5V volts.The input voltage minimum is 2.7V volts.
MIC2076-1YM Features
Supplied from 5V
Resistance of 90mOhm
MIC2076-1YM Applications
There are a lot of Microchip Technology MIC2076-1YM Power Switches ICs applications.
- Low Voltage I/O System Power
- Hot-Swap Systems
- Wireless Headsets
- USB Power Distribution
- Handheld Devices
- Solid State Drivers
- Portable Devices
- Solid-State Drives
- Mobile Communication Devices
- Notebook PC
