MIC2076-2YM
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e4 |
| Feature | Slew Rate Controlled, Status Flag |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 90mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Current Rating | 1.25A |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MIC2076 |
| Number of Outputs | 2 |
| Output Type | N-Channel |
| Max Output Current | 500mA |
| Interface | On/Off |
| Nominal Supply Current | 20μA |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Turn On Delay Time | 5 μs |
| Switch Type | General Purpose |
| Min Input Voltage | 2.7V |
| Max Input Voltage | 5.5V |
| Nominal Input Voltage | 5.5V |
| Turn-Off Delay Time | 100 μs |
| Ratio - Input:Output | 1:2 |
| Voltage - Load | 2.7V~5.5V |
| Fault Protection | Current Limiting (Fixed), Over Temperature, UVLO |
| Turn On Time | 5000 μs |
| Output Peak Current Limit-Nom | 0.9A |
| Rds On (Typ) | 90m Ω |
| Drain to Source Resistance | 140mOhm |
| Built-in Protections | OVER CURRENT; THERMAL; UNDER VOLTAGE |
| Output Current Flow Direction | SINK |
| Height | 1.63mm |
| Length | 5mm |
| Width | 3.99mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MIC2076-2YM Overview
A Tube is used to package it.The 8-SOIC (0.154, 3.90mm Width) package contains it.The mounting type of the LED driver is Surface Mount.The switch type of this switch is General Purpose.The temperature should be set to -40°C~85°C TA to ensure reliable functioning.It is possible to use 2 outputs in the lighting driver.To operate, it needs a supply voltage of Not Required.A maximum voltage of N-Channel volts is available from the output of this LED driver.Features of the lighting driver are Slew Rate Controlled, Status Flag.The MIC2076 family consists of this type.A total of 8 terminations have been found in it.It is necessary to use the 8 pins in order to operate the LED driver.As far as the lighting driver is concerned, there are 1 functions.The maximum output current drops to 500mA in order to meet the operation criteria.High efficiency is possible when the supply voltage is set to 5V.It is positioned in the direction of Surface Mount.There is 90mOhm resistance on the LED driver.This LED driver can handle voltages up to 5.5V volts.As far as input voltage goes, it has a minimum of 2.7V volts.
MIC2076-2YM Features
Supplied from 5V
Resistance of 90mOhm
MIC2076-2YM Applications
There are a lot of Microchip Technology MIC2076-2YM Power Switches ICs applications.
- Wireless Modem Data Cards
- Hot Swap
- USB Power Distribution
- Portable/Handheld Devices
- PC Cards
- Set-Top Boxes
- Low Voltage I/O System Power
- Storage Drives
- PDAs
- Notebook and Tablet Computers
