MIC2166YMME
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) Exposed Pad |
| Number of Pins | 10 |
| Supplier Device Package | 10-MSOP-EP |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tube |
| Published | 2010 |
| Series | Hyper Speed Control® |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Base Part Number | MIC2166 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 5.5V |
| Output Type | Transistor Driver |
| Max Supply Voltage | 28V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 950μA |
| Output Configuration | Positive |
| Output Current | 25A |
| Voltage - Supply (Vcc/Vdd) | 4.5V~28V |
| Control Features | Enable, Power Good |
| Max Output Voltage | 5.5V |
| Topology | Buck |
| Min Input Voltage | 4.5V |
| Frequency - Switching | 600kHz |
| Max Input Voltage | 28V |
| Synchronous Rectifier | Yes |
| Max Duty Cycle | 82 % |
| Isolation | Non-Isolated |
| Duty Cycle (Max) | 82% |
| Clock Sync | No |
| Output Phases | 1 |
| Number of Output Phases | 1 |
| Height | 860μm |
| Length | 3mm |
| Width | 3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
MIC2166YMME Overview
With a 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) Exposed Pad package, the switching controller is suitable for a wide range of applications. 1 outputs can be generated with the dc motor controller. PMIC packaging is solid with a Tube enclosure. With Transistor Driver dc switching's output (s), it is able to handle it. dc controls with 4.5V~28V voltage are supplied and operated. Worked in an dc switcher with a -40°C~125°C TJ rating. Using this switching controller, it is possible to switch at 600kHz. The Surface Mount value makes it suitable for general dc dc regulator. To provide efficient switching control, Enable, Power Good is included in the dcdc regulator. Other relevant dc to dc converter ics can be found by searching "MIC2166". 10 pins are present on switching converter. As determined by the test statistics, the output voltage of DC regulator is 5.5V. In most cases, the output current of the dc dc regulator will be 25A, so note that when you start the project. During power-up and power-down, the maximum duty cycle of the voltage regulator dc to dc is set to 82 %. The Surface Mount makes DC switcher suitable for most applications and prototypes. A temperature -40°C lower than -40°C should be maintained. At a temperature around 125°C degrees Celsius, dc regulator should be running. There are several dc to dc voltage regulator in the Hyper Speed Control? series. The maximum input voltage of this dc switcher is 28V, so users must limit the voltage accordingly. Its supplier dc dc controller package would be 10-MSOP-EP. Voltage 4.5V must be supplied. Datasheets indicate that the switching converter can output 5.5V volts at its maximum. It runs on a 950μA supply current. The controller switches with phase number 1. In terms of maximum supply voltage, switching voltage regulators is rated 28V.
MIC2166YMME Features
Transistor Driver Outputs
Switching Frequency: 600kHz
Enable, Power Good
Max Duty Cycle: 82 %
MIC2166YMME Applications
There are a lot of Microchip Technology MIC2166YMME DC to DC converter applications.
- Linear guide
- Wind power
- Household control circuits
- seismic instrument power circuits
- Planers
- Thermal power
- Surface processing equipment
- Printing
- Balance equipment
- Computer rooms
