MIC2182YM
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Frequency | 330kHz |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MIC2182 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 6V |
| Output Type | Transistor Driver |
| Max Output Current | 20A |
| Input Voltage-Nom | 15V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 20mA |
| Voltage - Supply (Vcc/Vdd) | 4.5V~32V |
| Quiescent Current | 600μA |
| Control Features | Enable, Soft Start |
| Input Voltage (Min) | 4.5V |
| Topology | Buck |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 300kHz |
| Input Voltage (Max) | 32V |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 60ns |
| Synchronous Rectifier | Yes |
| Fall Time (Typ) | 60 ns |
| Switcher Configuration | PUSH-PULL |
| Max Duty Cycle | 86 % |
| Isolation | Non-Isolated |
| Height | 1.64mm |
| Length | 10mm |
| Width | 3.99mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MIC2182YM Overview
It comes in the 16-SOIC (0.154, 3.90mm Width) package, which makes switching controller suitable for most applications. For 1 outputs, the dc motor controller is appropriate. Tube is the solid enclosure in which PMIC is packaged. With Transistor Driver dc switching's output (s), it is able to handle it. This dc control has a supply voltage and operating voltage of 4.5V~32V. Qualified to work in a -40°C~85°C TA dc switcher. The switching controller can be switched at 300kHz. As it has a Surface Mount value, it can be used for general dc dc regulator. Switching control is made easier with the dcdc regulator's Enable, Soft Start. The switch converters are connected to an analog IC with a SWITCHING CONTROLLER output. Switching converters are designed with the terminal (s) at position DUAL . The 16 terminations can be used for a wide range of dc switching. To name a few of the control techniques these dc dc converter ics adapt, it includes PULSE WIDTH MODULATION. There is a DC switcher's nominal voltage of 15V. MIC2182 can be used to locate other relevant dc to dc converter ics. Total pins of switching converter are 16. It is recommended to use 4.5V as the minimum input voltage of dc dc voltage regulator. A 6V voltage of DC regulator was detected in the test statistics. The dc to dc regulator can only accept 32V input voltage. If you start a project, note down the dc dc regulator's usual output current of 20mA. Power-up and power-down reliability is ensured voltage regulator dc to dc by setting the maximum duty cycle to 86 %. Because of DC switcher's Surface Mount, it is suitable for most prototype designs and applications. There is 330kHz frequency setting on the switching controller. In a dormant state, the dc switching uses 600μA. A dc switcher can only produce an output current of 20A.
MIC2182YM Features
Transistor Driver Outputs
Switching Frequency: 300kHz
Enable, Soft Start
PULSE WIDTH MODULATION
Max Duty Cycle: 86 %
Frequency: 330kHz
MIC2182YM Applications
There are a lot of Microchip Technology MIC2182YM DC to DC converter applications.
- Special machining machine tools
- Low output voltage switching power supply circuits
- seismic instrument power circuits
- Motor controller circuits
- Household control circuits
- Thermal power
- Planers
- Various precision measuring detectors
- Emergency lighting monitoring equipment
- Industrial robots
