MIC2182YM-TR
| Parameters | |
|---|---|
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2002 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | MATTE TIN |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MIC2182 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 6V |
| Output Type | Transistor Driver |
| Max Output Current | 20A |
| Input Voltage-Nom | 15V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 20mA |
| Voltage - Supply (Vcc/Vdd) | 4.5V~32V |
| Control Features | Enable, Soft Start |
| Input Voltage (Min) | 4.5V |
| Topology | Buck |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 300kHz |
| Input Voltage (Max) | 32V |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 60ns |
| Synchronous Rectifier | Yes |
| Fall Time (Typ) | 60 ns |
| Switcher Configuration | PUSH-PULL |
| Max Frequency | 330kHz |
| Max Duty Cycle | 86 % |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
MIC2182YM-TR Overview
The switching controller fits in the 16-SOIC (0.154, 3.90mm Width) package and is ideal for most applications. The dc motor controller is adquate to generate for 1 outputs. PMIC packaging is solid with a Tape & Reel (TR) enclosure. There are Transistor Driver dc switching's output (s) that it can handle. dc control's supply and operating voltages are 4.5V~32V. Qualified to work in a -40°C~85°C TA dc switcher. Using this switching controller, it is possible to switch at 300kHz. The Surface Mount value makes it suitable for general dc dc regulator. The dcdc regulator features Enable, Soft Start for efficient switching control. An analog IC with the SWITCHING CONTROLLER signal is connected to the switch converters. DUAL are the position of the terminal of the switching converters. Different dc switching's functions can be applied to 16 terminations. Some of the control techniques used by these dc dc converter ics are PULSE WIDTH MODULATION. The nominal DC switcher's voltage input is 15V. Other relevant dc to dc converter ics can be found by searching "MIC2182". In total, switching converter has 16 pins. dc dc voltage regulators should have a minimum input voltage of 4.5V. According to the test statistics, DC regulator outputs 6V voltage. A maximum voltage of 32V is accepted by the dc to dc regulator as an input voltage. If you are starting a new project, you should note the dc dc regulator's typical output current is 20mA. During power-up and power-down, the maximum duty cycle of the voltage regulator dc to dc is set to 86 %. The Surface Mount makes DC switcher suitable for most applications and prototypes. It is estimated that this dc regulatorhas a maximum frequency of 330kHz. DC switchers cannot produce output currents greater than 20A.
MIC2182YM-TR Features
Transistor Driver Outputs
Switching Frequency: 300kHz
Enable, Soft Start
PULSE WIDTH MODULATION
Max Duty Cycle: 86 %
MIC2182YM-TR Applications
There are a lot of Microchip Technology MIC2182YM-TR DC to DC converter applications.
- Photovoltaic power
- Printing
- CMM
- Computed tomography (CT)
- Computer rooms
- Remotely powered electric motors
- Sink circuits
- Energy management systems
- Post equipment
- Shearing machines
