MIC2182YSM
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 16 |
| Supplier Device Package | 16-SSOP |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2004 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Frequency | 330kHz |
| Base Part Number | MIC2182 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 6V |
| Output Type | Transistor Driver |
| Max Output Current | 20A |
| Max Supply Voltage | 32V |
| Output Configuration | Positive |
| Output Current | 20mA |
| Voltage - Supply (Vcc/Vdd) | 4.5V~32V |
| Quiescent Current | 600μA |
| Control Features | Enable, Soft Start |
| Max Output Voltage | 6V |
| Topology | Buck |
| Min Input Voltage | 4.5V |
| Frequency - Switching | 300kHz |
| Max Input Voltage | 32V |
| Rise Time | 60ns |
| Synchronous Rectifier | Yes |
| Fall Time (Typ) | 60 ns |
| Min Output Voltage | 1.25V |
| Max Duty Cycle | 86 % |
| Isolation | Non-Isolated |
| Duty Cycle (Max) | 86% |
| Clock Sync | Yes |
| Output Phases | 1 |
| Number of Output Phases | 1 |
| Height | 1.646mm |
| Length | 10mm |
| Width | 3.99mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MIC2182YSM Overview
With a 16-SSOP (0.209, 5.30mm Width) package, the switching controller is suitable for a wide range of applications. There is sufficient capacity to generate switching controller for outputs 1. The pmic is packaged in Tube solid enclosure. Transistor Driver dc switching's outputs (s) can be handled by it. The supply and operating voltage of the dc control are 4.5V~32V. Worked in an dc switcher with a -40°C~85°C TA rating. The switching controller can be switched at 300kHz. Surface Mount makes it suitable for general dc dc regulator. Enable, Soft Start is used for efficient switching control in the dcdc regulator. Searching "MIC2182" will return other relevant dc to dc converter ics. There are a total of 16 pins on switching converter. Based on the test statistics, DC regulator outputs voltage 6V. If you are starting a new project, you should note the dc dc regulator's typical output current is 20mA. The maximum duty cycle of this voltage regulator dc to dc is set to 86 % to ensure reliability during power-up and power-down. Because of DC switcher's Surface Mount, it is suitable for most prototype designs and applications. The switching controller works at a frequency of 330kHz. The temperature should be at least -40°C. DC regulator should run at a temperature 85°C higher than 85°C. When the dc switching is dormant, it uses 600μA. In order to ensure the dc switcher's functionality, users must limit the voltage to 32V due to the dc switcher's maximum input voltage. Its supplier dc dc controller package is 16-SSOP. 4.5V is the required supply voltage. There will be 20A output current greater than 20A from the dc switcher. The datasheet indicates that the switching converter can output 6V volts at its maximum. Lowest voltage output of the voltage controller must be greater than 1.25V. With this controller, the phase is 1. In terms of maximum supply voltage, switching voltage regulators is rated 32V.
MIC2182YSM Features
Transistor Driver Outputs
Switching Frequency: 300kHz
Enable, Soft Start
Max Duty Cycle: 86 %
Frequency: 330kHz
MIC2182YSM Applications
There are a lot of Microchip Technology MIC2182YSM DC to DC converter applications.
- Printing
- Surge protection circuits
- USB circuits
- Gear/thread machining machines
- Flexible manufacturing cells
- Electrical distribution systems
- Smoke prevention equipment
- Surface processing equipment
- Current source circuits
- Shearing machines
