MIC708MY
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Power Dissipation | 400mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MIC708 |
| Output | Complementary |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.4V |
| Operating Supply Current | 60μA |
| Nominal Supply Current | 60μA |
| Power Dissipation | 400mW |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active High/Active Low |
| Voltage - Threshold | 4.4V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.06mA |
| Min Reset Threshold Voltage | 4.25V |
| Max Reset Threshold Voltage | 4.5V |
| Threshold Voltage | +4.4V |
| Length | 4.93mm |
| Width | 3.94mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MIC708MY Overview
This voltage supervisor has a total of 8 mounting terminals that can be used for mounting. Power management is packaged in a Tube way. In this PMIC, you can find 1 functions for your reference. This power management is made up of 1 channels which are available in a series format. To assist you, this PMIC includes 8-SOIC (0.154, 3.90mm Width) functions. Compared to other Simple Reset/Power-On Reset products, this PMIC has a lot of benefits to offer. IC management is specified that the package peak reflow temperature should be 260. A supply voltage of 5V is used to conduct the PMIC chip. IC management is possible to find a succession of 1 voltages that have been checked. Surface Mount mounts power management on the wall. This power management system has 8 pins. It is recommended that Vsup should not be less than 1.4V for this IC power. The maximum supply voltage (Vsup) is not to exceed 5.5V volts in this IC management. Power management recommends the Surface Mount mounting type. This power management is the recommended temperature range for the supervisors: -40°C~85°C TA. While in operation, this supervisor has a voltage output of Complementary. In order to maintain a stable supply current for the power management, 60μA is the recommended value. A similar IC managements number of the manufacturer can always be found by using MIC708, the base power ics number.
MIC708MY Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.4V
60μA operating supply current
MIC708MY Applications
There are a lot of Microchip Technology MIC708MY Voltage Supervisors applications.
- Leakage current detection
- Electronics installed in the vehicle
- FPGA design
- Unattended substation automation
- Display equipment
- Computer applications
- Stable power system
- Detection of phase sequence
- Network equipment
- Consumer electronics
