MM74C74N
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Supplier Device Package | 14-PDIP |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2002 |
| Series | 74C |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Voltage - Supply | 3V~15V |
| Frequency | 8MHz |
| Base Part Number | 74C74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Number of Circuits | 2 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | 3V |
| Output Current | 8mA |
| Number of Bits | 2 |
| Clock Frequency | 8MHz |
| Propagation Delay | 300 ns |
| Turn On Delay Time | 70 ns |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 60μA |
| Current - Output High, Low | 8mA 8mA |
| Number of Gates | 2 |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 110ns @ 10V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | 8mA |
| Input Capacitance | 5pF |
| Low Level Output Current | 8mA |
| Number of Input Lines | 1 |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
MM74C74N Overview
It is packaged in the way of 14-DIP (0.300, 7.62mm). D flip flop is included in the Tubepackage. T flip flop uses Differentialas the output. The trigger it is configured with uses Positive Edge. Through Holemounts this electrical part. The JK flip flop operates with an input voltage of 3V~15V volts. It is at -55°C~125°C TAdegrees Celsius that the system is operating. The type of this D latch is D-Type. In FPGA terms, D flip flop is a type of 74Cseries FPGA. It should not exceed 8MHzin terms of its output frequency. D latch consists of 2 elements. As a result, it consumes 60μA of quiescent current without being affected by external factors. JK flip flop belongs to 74C74 family. Its input capacitance is 5pF farads. There is an electronic component mounted in the way of Through Hole. With its 14pins, it is designed to work with most electronic flip flops. This device has the clock edge trigger type of Positive Edge. 2bits are used in its design. Using 2 circuits, it is highly flexible. It offers maximum design flexibility with its output current of 8mA. In order to operate, the chip has 1 output lines. There are 1 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply. The high level output current is set to 8mA. There is no low level output current set at 8mA. The operating temperature should be lower than 125°C. A temperature above -55°Cshould be used for the operation. It is powered by 3V as its minimum supply voltage. There is a maximum voltage support of 15V. It is possible to achieve 8MHz frequencies. In its basic building block, there are 2 gates.
MM74C74N Features
Tube package
74C series
14 pins
2 Bits
2 gates
MM74C74N Applications
There are a lot of ON Semiconductor MM74C74N Flip Flops applications.
- Consumer
- Differential Individual
- Communications
- CMOS Process
- Pattern generators
- Clock pulse
- Single Down Count-Control Line
- Patented noise
- Convert a momentary switch to a toggle switch
- Shift registers
