MM74HC4066N
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Supplier Device Package | 14-PDIP |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 70Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Max Power Dissipation | 600mW |
| Base Part Number | 74HC4066 |
| Number of Outputs | 4 |
| Number of Channels | 4 |
| Number of Circuits | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Power Dissipation | 600mW |
| Max Supply Current | 8μA |
| Number of Bits | 4 |
| Throw Configuration | SPST |
| Turn On Delay Time | 100 ns |
| Number of Inputs | 4 |
| Supply Type | Single |
| Turn-Off Delay Time | 168 ns |
| Number of Gates | 4 |
| -3db Bandwidth | 100MHz |
| On-State Resistance (Max) | 70Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 20nA |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 10ns, 30ns |
| Channel-to-Channel Matching (ΔRon) | 5Ohm |
| Crosstalk | -50dB @ 1MHz |
| Voltage - Supply, Single (V+) | 2V~12V |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
MM74HC4066N Overview
This electronic part is conveniently packaged in 14-DIP (0.300, 7.62mm), making it easy to ship abroad. High reliability is ensured by the advanced packaging method Tube. Through Hole is where this multiplexer is located. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Increasing operating temperature to around -40°C~85°C TA. As a result of its 4 channels, this electronic component provides high-quality output. A SPST - NO switching circuit is used to build these analog multiplexers. There are 4 circuits in this multiplexer. Try searching for the analog switch ic with 74HC4066 if you are looking for variants. It has an internal resistance of 70Ohm. You can find the functions of the 14 pins in the datasheets. Multiplexers should not be powered above 12V in normal situations. A cost-effective Single supply type analogue multiplexer. The lowest voltage fed to the electronic component should be 2V. The voltage required by this switch device is 2V~12V, draining from a single voltage supply. Putting voltage greater than 8μA on the multiplexer may cause damage. The electrical component supports 4 inputs. It is not recommended to operate the switches in an environment with a temperature higher than 85°C. Multiplexer ics with 4 outputs are available. It is offered by suppliers in package 14-PDIP. It is capable of carrying out 4-bit operation.
MM74HC4066N Features
4 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 100MHz
4-Bit
MM74HC4066N Applications
There are a lot of ON Semiconductor MM74HC4066N Analog Switches & Multiplexers ICs applications.
- Battery-powered systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- ISDN NT1/TA
- Data Acquisition Systems
- CSU
- SDH/SONET multiplexers
- Microprocessor controlled systems
- Relay replacements
- RGB switches
- Signal routing between systems
