MM74HC574MTC
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 191mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2005 |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 4.5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74HC574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 35MHz |
| Propagation Delay | 155 ns |
| Turn On Delay Time | 18 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 7.8mA 7.8mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 27ns @ 6V, 150pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 24000000Hz |
| Height | 900μm |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MM74HC574MTC Overview
It is packaged in the way of 20-TSSOP (0.173, 4.40mm Width). There is an embedded version in the package Tube. The output it is configured with uses Tri-State, Non-Inverted. JK flip flop uses Positive Edgeas the trigger. Surface Mountmounts this electrical part. It operates with a supply voltage of 2V~6V. In this case, the operating temperature is -40°C~85°C TA. This logic flip flop is classified as type D-Type. FPGAs belonging to the 74HCseries contain this type of chip. This D flip flop should not have a frequency greater than 35MHz. In total, there are 1 elements. There is a consumption of 8μAof quiescent energy. The number of terminations is 20. The 74HC574 family contains it. The power source is powered by 4.5V. Its input capacitance is 5pFfarads. A device of this type belongs to the family of HC/UH. Surface Mount mounts this electronic component. A total of 20pins are provided on this board. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. This device has the base part number FF/Latches. An electronic part designed with 8bits is used in this application. Vsup reaches 6V, the maximal supply voltage. Normal operation requires a supply voltage (Vsup) above 2V. Its flexibility is enhanced by 8 circuits. The power supply is 2/6V. A total of 2ports are embedded in the D flip flop. In order to operate, the chip has 3 output lines.
MM74HC574MTC Features
Tube package
74HC series
20 pins
8 Bits
2/6V power supplies
MM74HC574MTC Applications
There are a lot of ON Semiconductor MM74HC574MTC Flip Flops applications.
- Individual Asynchronous Resets
- Set-reset capability
- Counters
- Shift Registers
- Data storage
- Clock pulse
- Matched Rise and Fall
- Consumer
- Patented noise
- Frequency division
