MM74HC574WM
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 801mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2005 |
| Series | 74HC |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Tin (Sn) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 4.5V |
| Base Part Number | 74HC574 |
| Function | Standard |
| Number of Outputs | 9 |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Channels | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 7.8mA |
| Number of Bits | 8 |
| Clock Frequency | 35MHz |
| Propagation Delay | 155 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 18 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 7.8mA 7.8mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 27ns @ 6V, 150pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 24000000Hz |
| Height | 2.35mm |
| Length | 13mm |
| Width | 7.6mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MM74HC574WM Overview
The item is packaged in 20-SOIC (0.295, 7.50mm Width)cases. As part of the package Tube, it is embedded. As configured, the output uses Tri-State, Non-Inverted. This trigger is configured to use Positive Edge. There is an electric part mounted in the way of Surface Mount. The JK flip flop operates at a voltage of 2V~6V. It is operating at -40°C~85°C TA. This logic flip flop is classified as type D-Type. The 74HCseries comprises this type of FPGA. You should not exceed 35MHzin the output frequency of the device. In total, it contains 1 elements. A total of 20terminations have been recorded. The 74HC574family includes it. Power is provided by a 4.5V supply. The input capacitance of this T flip flop is 5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. A device of this type belongs to the family of HC/UH. In this case, the electronic component is mounted in the way of Surface Mount. It is designed with 20 pins. The clock edge trigger type for this device is Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. An electronic part with 8bits has been designed. Vsup reaches its maximum value at 6V. A normal operating voltage (Vsup) should remain above 2V. An electrical current of 2/6V volts is applied to it. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. With an output current of 7.8mA, it is possible to design the device in any way you want. In order for the chip to function, it has 3output lines. Quiescent current is consumed by the D latch in the amount of 8μA. It is reported that there are 8 channels.
MM74HC574WM Features
Tube package
74HC series
20 pins
8 Bits
2/6V power supplies
MM74HC574WM Applications
There are a lot of ON Semiconductor MM74HC574WM Flip Flops applications.
- Shift registers
- Digital electronics systems
- Frequency Dividers
- Storage registers
- Frequency Divider circuits
- Matched Rise and Fall
- Parallel data storage
- Bus hold
- Balanced 24 mA output drivers
- Test & Measurement
