MM74HC74AM
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Supplier Device Package | 14-SOIC |
| Weight | 240.999296mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| Series | 74HC |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Termination | SMD/SMT |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 2V~6V |
| Frequency | 72MHz |
| Base Part Number | 74HC74 |
| Function | Set(Preset) and Reset |
| Number of Outputs | 4 |
| Output Type | Differential |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Number of Channels | 2 |
| Voltage | 5V |
| Number of Circuits | 2 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Output Current | 5.2mA |
| Number of Bits | 2 |
| Clock Frequency | 94MHz |
| Propagation Delay | 110 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 12 ns |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Number of Inputs | 1 |
| Current - Output High, Low | 5.2mA 5.2mA |
| Number of Gates | 2 |
| Number of Bits per Element | 1 |
| Max Frequency | 28MHz |
| Max Propagation Delay @ V, Max CL | 19ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -5.2mA |
| Input Capacitance | 5pF |
| Low Level Output Current | 5.2mA |
| Number of Input Lines | 1 |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.5mm |
| Length | 8.75mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MM74HC74AM Overview
The package is in the form of 14-SOIC (0.154, 3.90mm Width). The Tubepackage contains it. There is a Differentialoutput configured with it. Positive Edgeis the trigger it is configured with. In this case, the electronic component is mounted in the way of Surface Mount. The JK flip flop operates with an input voltage of 2V~6V volts. A temperature of -40°C~85°C TAis used in the operation. D-Typeis the type of this D latch. In this case, it is a type of FPGA belonging to the 74HC series. A frequency of 94MHzshould not be exceeded by its output. D latch consists of 2 elements. It consumes 4μA of quiescent current without being affected by external factors. If you search by 74HC74, you will find similar parts. The input capacitance of this T flip flop is 5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. It is mounted by the way of Surface Mount. This board is designed with 14pins on it. Its clock edge trigger type is Positive Edge. The design is based on 2bits. Its superior flexibility is attributed to its use of 2 circuits. With an output current of 5.2mA, it is possible to design the device in any way you want. It has 1 output lines to operate. A total of 1input lines have been provided. It consumes a total of 4μA quiescent current at any given time. A -5.2mAvalue is set for the high level output current. 5.2mA is the low level output current. A temperature below 85°Cshould be used for operation. A temperature above -40°Cshould be used for the operation. The minimum voltage required for operation is 2V. 6Vis the maximum supply voltage it supports. This frequency can be achieved at 72MHz. 2 channels are available. In its basic building block, there are 2 gates. The inputs employed are 1.
MM74HC74AM Features
Tube package
74HC series
14 pins
2 Bits
2 gates
MM74HC74AM Applications
There are a lot of ON Semiconductor MM74HC74AM Flip Flops applications.
- ESD protection
- Matched Rise and Fall
- Shift Registers
- Automotive
- Reduced system switching noise
- Counters
- Modulo – n – counter
- Storage registers
- Differential Individual
- Functionally equivalent to the MC10/100EL29
