MM74HC74AMTC
| Parameters | |
|---|---|
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Output Current | 5.2mA |
| Clock Frequency | 94MHz |
| Propagation Delay | 40 ns |
| Turn On Delay Time | 12 ns |
| Family | HC/UH |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max I(ol) | 0.004 A |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 19ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 900μm |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Weight | 55.3mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 4.5V |
| Base Part Number | 74HC74 |
MM74HC74AMTC Overview
The flip flop is packaged in 14-TSSOP (0.173, 4.40mm Width). As part of the package Tube, it is embedded. Differentialis the output configured for it. The trigger it is configured with uses Positive Edge. Surface Mountmounts this electrical part. With a supply voltage of 2V~6V volts, it operates. In this case, the operating temperature is -40°C~85°C TA. D-Typedescribes this flip flop. JK flip flop is a part of the 74HCseries of FPGAs. Its output frequency should not exceed 94MHz Hz. As a result, it consumes 4μA of quiescent current without being affected by external factors. There have been 14 terminations. D latch belongs to the 74HC74 family. A voltage of 4.5V is used to power it. Its input capacitance is 5pFfarads. HC/UHis the family of this D flip flop. This electronic part is mounted in the way of Surface Mount. Basically, it is designed with a set of 14 pins. This device exhibits a clock edge trigger type of Positive Edge. This part is included in FF/Latches. It reaches the maximum supply voltage (Vsup) at 6V. A normal operating voltage (Vsup) should remain above 2V. Despite its superior flexibility, it relies on 2 circuits to achieve it. In addition to its maximum design flexibility, the output current of the T flip flop is 5.2mA. In order for the chip to function, it has 1output lines.
MM74HC74AMTC Features
Tube package
74HC series
14 pins
MM74HC74AMTC Applications
There are a lot of ON Semiconductor MM74HC74AMTC Flip Flops applications.
- Latch-up performance
- Pattern generators
- Differential Individual
- Convert a momentary switch to a toggle switch
- Data transfer
- Parallel data storage
- Circuit Design
- Synchronous counter
- Bus hold
- Computers
