MM74HCT273MTCX
| Parameters | |
|---|---|
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74HCT273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Channels | 8 |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Clock Frequency | 68MHz |
| Propagation Delay | 30 ns |
| Turn On Delay Time | 22 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 4.8mA 4.8mA |
| Max I(ol) | 0.004 A |
| Max Propagation Delay @ V, Max CL | 37ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 6pF |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 191mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
MM74HCT273MTCX Overview
The package is in the form of 20-TSSOP (0.173, 4.40mm Width). Package Tape & Reel (TR)embeds it. T flip flop uses Non-Invertedas the output. There is a trigger configured with Positive Edge. In this case, the electronic component is mounted in the way of Surface Mount. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. A temperature of -40°C~85°C TAis used in the operation. D-Typeis the type of this D latch. This type of FPGA is a part of the 74HCT series. In order for it to function properly, its output frequency should not exceed 68MHz. D latch consists of 1 elements. As a result, it consumes 8μA quiescent current. The number of terminations is 20. This D latch belongs to the family of 74HCT273. The power supply voltage is 5V. A 6pFfarad input capacitance is provided by this T flip flop. In this case, the D flip flop belongs to the HCTfamily. In this case, the electronic component is mounted in the way of Surface Mount. Basically, it is designed with a set of 20 pins. The clock edge trigger type for this device is Positive Edge. The RS flip flops belongs to FF/Latches base part number. This flip flop is designed with 8 Bits. On the basis of its reliable performance, this D flip flop is well suited for use with TAPE AND REEL. A total of 5V power supplies are needed to run it. Optimal efficiency requires a supply voltage of 5V. Currently, there are 8 channels available.
MM74HCT273MTCX Features
Tape & Reel (TR) package
74HCT series
20 pins
8 Bits
5V power supplies
MM74HCT273MTCX Applications
There are a lot of ON Semiconductor MM74HCT273MTCX Flip Flops applications.
- High Performance Logic for test systems
- QML qualified product
- Shift Registers
- Safety Clamp
- Reduced system switching noise
- Consumer
- Latch
- Circuit Design
- Functionally equivalent to the MC10/100EL29
- Data storage
