MM74HCT273SJX
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 481.5mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| Series | 74HCT |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74HCT273 |
| Function | Master Reset |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Clock Frequency | 68MHz |
| Propagation Delay | 37 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 22 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 4.8mA 4.8mA |
| Max I(ol) | 0.004 A |
| Max Propagation Delay @ V, Max CL | 37ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 6pF |
| Clock Edge Trigger Type | Positive Edge |
| Width | 5.3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MM74HCT273SJX Overview
The item is packaged in 20-SOIC (0.209, 5.30mm Width)cases. It is contained within the Tape & Reel (TR)package. In the configuration, Non-Invertedis used as the output. JK flip flop uses Positive Edgeas the trigger. Surface Mountmounts this electrical part. A voltage of 4.5V~5.5Vis required for its operation. It is operating at -40°C~85°C TA. D-Typedescribes this flip flop. In FPGA terms, D flip flop is a type of 74HCTseries FPGA. In order for it to function properly, its output frequency should not exceed 68MHz. A total of 1elements are contained within it. 20terminations have occurred. The object belongs to the 74HCT273 family. The D flip flop is powered by a voltage of 5V . The input capacitance of this T flip flop is 6pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. This D flip flop belongs to the family of HCT. A part of the electronic system is mounted in the way of Surface Mount. This board is designed with 20pins on it. A Positive Edgeclock edge trigger is used in this device. There is a FF/Latchesbase part number assigned to the RS flip flops. The flip flop is designed with 8bits. Despite its superior flexibility, it relies on 8 circuits to achieve it. Due to its reliability, this T flip flop is well suited for TAPE AND REEL. The power supply is 5V. For high efficiency, the supply voltage should be kept at 5V. Quiescent current is consumed by the D latch in the amount of 8μA.
MM74HCT273SJX Features
Tape & Reel (TR) package
74HCT series
20 pins
8 Bits
5V power supplies
MM74HCT273SJX Applications
There are a lot of ON Semiconductor MM74HCT273SJX Flip Flops applications.
- Test & Measurement
- Parallel data storage
- ESD protection
- Common Clocks
- Bounce elimination switch
- Data transfer
- Communications
- Reduced system switching noise
- Safety Clamp
- Control circuits
