MM74HCT374MTCX
| Parameters | |
|---|---|
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 30MHz |
| Propagation Delay | 46 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 30 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 7.2mA 7.2mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 46ns @ 5V, 150pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 24000000Hz |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 191mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74HCT374 |
| Function | Standard |
MM74HCT374MTCX Overview
As a result, it is packaged as 20-TSSOP (0.173, 4.40mm Width). There is an embedded version in the package Tape & Reel (TR). T flip flop is configured with an output of Tri-State, Non-Inverted. It is configured with a trigger that uses Positive Edge. Surface Mountis occupied by this electronic component. The JK flip flop operates with an input voltage of 4.5V~5.5V volts. -40°C~85°C TAis the operating temperature. It belongs to the type D-Typeof flip flops. JK flip flop is a part of the 74HCTseries of FPGAs. You should not exceed 30MHzin the output frequency of the device. The list contains 1 elements. The number of terminations is 20. It is a member of the 74HCT374 family. A voltage of 5V is used as the power supply for this D latch. Its input capacitance is 10pF farads. A device of this type belongs to the family of HCT. It is mounted in the way of Surface Mount. This board is designed with 20pins on it. This device exhibits a clock edge trigger type of Positive Edge. The part you are looking for is included in FF/Latches. There are 8bits in its design. Its flexibility is enhanced by 8 circuits. Due to its reliability, this T flip flop is well suited for TAPE AND REEL. It runs on 5Vvolts of power. The flip flop contains 2ports. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. It operates with 3 output lines. It consumes 8μA of quiescent current without being affected by external factors.
MM74HCT374MTCX Features
Tape & Reel (TR) package
74HCT series
20 pins
8 Bits
5V power supplies
MM74HCT374MTCX Applications
There are a lot of ON Semiconductor MM74HCT374MTCX Flip Flops applications.
- Asynchronous counter
- Power down protection
- Event Detectors
- Shift Registers
- Balanced 24 mA output drivers
- Single Down Count-Control Line
- Digital electronics systems
- Counters
- Data Synchronizers
- High Performance Logic for test systems
