MM74HCT574MTCX
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 191mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74HCT574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Channels | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 33MHz |
| Propagation Delay | 30 ns |
| Turn On Delay Time | 18 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 7.2mA 7.2mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 30ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MM74HCT574MTCX Overview
It is embeded in 20-TSSOP (0.173, 4.40mm Width) case. It is included in the package Tape & Reel (TR). T flip flop uses Tri-State, Non-Invertedas its output configuration. JK flip flop uses Positive Edgeas the trigger. The electronic part is mounted in the way of Surface Mount. A voltage of 4.5V~5.5Vis used as the supply voltage. It is at -40°C~85°C TAdegrees Celsius that the system is operating. D-Typedescribes this flip flop. The FPGA belongs to the 74HCT series. It should not exceed 33MHzin its output frequency. A total of 1 elements are present. There is 8μA quiescent consumption. It has been determined that there have been 20 terminations. Members of the 74HCT574family make up this object. The D flip flop is powered by a voltage of 5V . The input capacitance of this JK flip flopis 10pF farads. The electronic device belongs to the HCTfamily. There is an electronic part mounted in the way of Surface Mount. This board is designed with 20pins on it. There is a clock edge trigger type of Positive Edgeon this device. There is a base part number FF/Latchesfor the RS flip flops. Flip flops designed with 8bits are used in this part. Considering its reliability, this T flip flop is well suited for TAPE AND REEL. The D latch operates on 5V volts. A total of 2ports are embedded in the D flip flop. If high efficiency is desired, the supply voltage should be kept at 5V. There are no output lines on the JK flip flop. Currently, there are 8 channels available.
MM74HCT574MTCX Features
Tape & Reel (TR) package
74HCT series
20 pins
8 Bits
5V power supplies
MM74HCT574MTCX Applications
There are a lot of ON Semiconductor MM74HCT574MTCX Flip Flops applications.
- Circuit Design
- Guaranteed simultaneous switching noise level
- Power down protection
- Count Modes
- Latch
- Shift Registers
- Storage Registers
- Storage registers
- Bounce elimination switch
- Individual Asynchronous Resets
