MM74HCT574N
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74HCT |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | MATTE TIN |
| Additional Feature | BROADSIDE VERSION OF 374 |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT APPLICABLE |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | NOT APPLICABLE |
| JESD-30 Code | R-PDIP-T20 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Supply Voltage-Max (Vsup) | 5.5V |
| Supply Voltage-Min (Vsup) | 4.5V |
| Number of Ports | 2 |
| Clock Frequency | 33MHz |
| Family | HCT |
| Current - Quiescent (Iq) | 8μA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 7.2mA 7.2mA |
| Output Polarity | TRUE |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 30ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Length | 26.075mm |
| Width | 7.62mm |
| RoHS Status | ROHS3 Compliant |
MM74HCT574N Overview
20-DIP (0.300, 7.62mm)is the way it is packaged. There is an embedded version in the package Tube. This output is configured with Tri-State, Non-Inverted. This trigger is configured to use Positive Edge. There is an electrical part that is mounted in the way of Through Hole. A voltage of 4.5V~5.5Vis required for its operation. It is operating at -40°C~85°C TA. Logic flip flops of this type are classified as D-Type. JK flip flop is a part of the 74HCTseries of FPGAs. There should be no greater frequency than 33MHzon its output. A total of 1elements are present in it. As a result, it consumes 8μA quiescent current. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. An input voltage of 5Vpowers the D latch. JK flip flop input capacitance is 10pF farads. HCTis the family of this D flip flop. It reaches the maximum supply voltage (Vsup) at 5.5V. It is imperative that the supply voltage (Vsup) is maintained above 4.5Vin order to ensure normal operation. A D flip flop with 2embedded ports is available. In addition, you can refer to the additinal BROADSIDE VERSION OF 374 of the D latch.
MM74HCT574N Features
Tube package
74HCT series
MM74HCT574N Applications
There are a lot of Rochester Electronics, LLC MM74HCT574N Flip Flops applications.
- Asynchronous counter
- QML qualified product
- Synchronous counter
- Modulo – n – counter
- Single Down Count-Control Line
- ESD performance
- Computers
- Circuit Design
- Count Modes
- Counters
