MM74HCT74MTC
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Weight | 55.3mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74HCT74 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Channels | 2 |
| Load Capacitance | 50pF |
| Clock Frequency | 27MHz |
| Propagation Delay | 35 ns |
| Turn On Delay Time | 21 ns |
| Family | HCT |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 2μA |
| Current - Output High, Low | 4.8mA 4.8mA |
| Max I(ol) | 0.004 A |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 35ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 5mm |
| Width | 4.4mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MM74HCT74MTC Overview
14-TSSOP (0.173, 4.40mm Width)is the packaging method. The Tubepackage contains it. As configured, the output uses Differential. This trigger uses the value Positive Edge. Surface Mountis in the way of this electric part. The JK flip flop operates with an input voltage of 4.5V~5.5V volts. A temperature of -40°C~85°C TAis used in the operation. This logic flip flop is classified as type D-Type. It is a type of FPGA belonging to the 74HCT series. It should not exceed 27MHzin its output frequency. Despite external influences, it consumes 2μAof quiescent current. 14terminations have occurred. JK flip flop belongs to 74HCT74 family. The power source is powered by 5V. Input capacitance of this device is 5pF farads. The electronic device belongs to the HCTfamily. A part of the electronic system is mounted in the way of Surface Mount. The 14pins are designed into the board. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. It is included in FF/Latches. In order for the device to operate, it requires 5V power supplies. For high efficiency, the supply voltage should be set to 5V. In order to operate, the chip has 1 output lines. 2 channels are available.
MM74HCT74MTC Features
Tube package
74HCT series
14 pins
5V power supplies
MM74HCT74MTC Applications
There are a lot of ON Semiconductor MM74HCT74MTC Flip Flops applications.
- Bounce elimination switch
- Single Up Count-Control Line
- Buffered Clock
- Storage registers
- Supports Live Insertion
- Automotive
- Guaranteed simultaneous switching noise level
- Counters
- 2 – Bit synchronous counter
- Balanced Propagation Delays
