MP5001DQ-LF-Z
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 10-VFDFN Exposed Pad |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e3 |
| Feature | Slew Rate Controlled, Status Flag |
| Pbfree Code | yes |
| Part Status | Not For New Designs |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Terminal Position | DUAL |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Pin Count | 10 |
| Number of Outputs | 1 |
| Qualification Status | Not Qualified |
| Output Type | N-Channel |
| Operating Supply Voltage | 10V |
| Supply Voltage-Min (Vsup) | 4V |
| Number of Channels | 1 |
| Interface | On/Off |
| Analog IC - Other Type | POWER SUPPLY SUPPORT CIRCUIT |
| Current - Output (Max) | 5A |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Adjustable Threshold | NO |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Min Input Voltage | 4V |
| Max Input Voltage | 10V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 4V~10V |
| Fault Protection | Current Limiting (Adjustable), Over Temperature, Over Voltage, UVLO |
| Rds On (Typ) | 44m Ω |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | ROHS3 Compliant |
MP5001DQ-LF-Z Overview
The LED driver's packaged as a Tape & Reel (TR).This package is included in 10-VFDFN Exposed Pad.This LED driving board is mounted using the mounting type Surface Mount.The switch type of this switch is General Purpose.To ensure reliable operation, the temperature should be set to -40°C~85°C TA.The LED driver has a total of 1 outputs.In order to operate, it requires a voltage supply of Not Required.There is a maximum output voltage of N-Channel volts on this LED driver.There are Slew Rate Controlled, Status Flag features available on the LED driving board.A total of 10 terminations have been recorded.It contains 1 functions.In this case, the LED driving board can produce only 5AV as its maximum output.It is possible to achieve a high level of efficiency with a supply voltage of 5V.The LED driver has a total of 10 pins.Normal operation requires Vsup above 4V.This LED driving board uses an analog IC POWER SUPPLY SUPPORT CIRCUIT.There are a total of 1 available channels.The supply voltage should be set at 10V for best efficiency.Its maximum input voltage is 10V volts.As a minimum input voltage, it requires 4V volts.
MP5001DQ-LF-Z Features
Supplied from 5V
1 channels
MP5001DQ-LF-Z Applications
There are a lot of Monolithic Power Systems Inc. MP5001DQ-LF-Z Power Switches ICs applications.
- PC Card Hot Swap
- Set-top-box
- Low Voltage I/O System Power
- Portable GPS Device
- Storage Drives
- Wireless Modem Data Cards
- Hot-Swap Systems
- Portable Devices
- Wireless/Networking Cards
- PC Cards
