MPC509AP
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Gold |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.053808g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 1.5kOhm |
| Max Power Dissipation | 7.5mW |
| Technology | CMOS |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | MPC509 |
| Pin Count | 16 |
| Number of Outputs | 1 |
| Operating Supply Voltage | 18V |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Operating Supply Current | 700μA |
| Nominal Supply Current | 1.5mA |
| Power Dissipation | 1.28W |
| Throw Configuration | 4PST |
| Turn On Delay Time | 200 ns |
| Logic Function | Multiplexer |
| Number of Inputs | 8 |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 1.5kOhm |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 20mA |
| Dual Supply Voltage | 9V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 500pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 5pF 12pF |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 200ns, 250ns (Typ) |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 500ns |
| Switch-off Time-Max | 500ns |
| Drain to Source Resistance | 1.3kOhm |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±5V~22V |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MPC509AP Overview
Packed in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. This high-reliability packaging method uses advanced packaging methods Tube. This analog switch is mounted in Through Hole. Multiplexers and demultiplexers have the same number of circuits 4:1. Temperatures around -40°C~85°C TA are extended for operation. Total terminations are 16. A 2 channel electronic part produces high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. It is injected into the electrical part body with 16 pins. Unlike digital switches, these are based on SP4T switching circuits. There are 2 circuits in this switch device. If you are looking for variants of the digital switch, trying search with MPC509. Analog switches have 1.5kOhm internal resistance. For details about the functions of 16 pins, please refer to the datasheets. Analogue multiplexer with a Dual supply type that is cost-effective. 700μA current would be enough for this multiplexer to operate. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. For dual power supplies, a voltage of at least 5V should be attached. The electronic component can function from 18V. Operating 8 inputs is required. There is 1.3kOhm resistance between the Drain and Source on this part. The analog switch ics includes 1 outputs.
MPC509AP Features
2 Channels
Switch Circuit: SP4T
700μA Supply Current
Drain-to-Source resistance: 1.3kOhm
MPC509AP Applications
There are a lot of Texas Instruments MPC509AP Analog Switches & Multiplexers ICs applications.
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Channel Banks
- Private Branch Exchange (PBX)
- ATM
- Mechanical reed relay replacement
- SONET
- MP3 players
- Data Acquisition Systems
- Public switching systems
- DVD-R
