MUX08FP
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 300Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | JFET |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MUX08 |
| Output | COMMON OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Power Dissipation | 247mW |
| Throw Configuration | DPST |
| Propagation Delay | 1.5 μs |
| Turn On Delay Time | 2 μs |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 2 μs |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 300Ohm |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 2.5pF 7pF |
| On-state Resistance Match-Nom | 75Ohm |
| Switch Time (Ton, Toff) (Max) | 2μs, 400ns |
| Channel-to-Channel Matching (ΔRon) | 21 Ω |
| Crosstalk | -70dB @ 500kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 2000ns |
| Switch-off Time-Max | 400ns |
| Normal Position | NO |
| Signal Current-Max | 0.025A |
| Height Seated (Max) | 5.33mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MUX08FP Overview
As the electronic part is packed in 16-DIP (0.300, 7.62mm), international shipping is convenient. This packaging method provides high reliability because it uses advanced packaging techniques. A switch device like this is mounted in Through Hole. Multiplexer and demultiplexer circuits have a number 8:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, 16 terminations have occurred. As a result of its 8 channels, this electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. Electronic part bodies are injected with 16 pins. Circuits number 1 make up this analogue multiplexer. Try searching for the analog switch ic with MUX08 if you are looking for variants. As far as internal resistance is concerned, it has 300Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. Multiplexer or Switches is a typical switch device. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 18V. A SINGLE-ENDED MULTIPLEXER analog IC is integrated into the board. The analog switch ic utilizes COMMON OUTPUT outputs in total. 15V operating voltages can be used with this electrical part.
MUX08FP Features
8 Channels
MUX08FP Applications
There are a lot of Analog Devices Inc. MUX08FP Analog Switches & Multiplexers ICs applications.
- SDH/SONET multiplexers
- MP3 players
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Modems
- Communication systems
- Audio and video routing
- Access Concentrators
- RGB switches
- Public switching systems
- Cross Connects
