MXD1810UR41+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-236-3, SC-59, SOT-23-3 |
| Number of Pins | 3 |
| Operating Temperature | -40°C~105°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 320mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.6V |
| Terminal Pitch | 0.95mm |
| Base Part Number | MXD1810 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 3 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 9μA |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 4.12V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 100ms Minimum |
| Min Reset Threshold Voltage | 4V |
| Max Reset Threshold Voltage | 4.24V |
| Threshold Voltage | +4.12V |
| Undervoltage Threshold | 4V |
| Overvoltage Threshold | 4.24V |
| Length | 2.92mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MXD1810UR41+T Overview
There are 3 terminals on this power management that allow it to be mounted. Packaging is in the form of a Tape & Reel (TR). To assist you, this IC power includes 1 functions. Depending on the power managment ic you are looking at, you can find a total of 1 channels. Please refer to power management for TO-236-3, SC-59, SOT-23-3 functions. As with other Simple Reset/Power-On Reset products, this IC management also offers a wide range of benefits. During the reflow process, a peak temperature of 260 is specified for the package. In a 3.6V supply voltage, the power management conducts. A supply voltage of 1 is used to conduct the PMIC chip. Surface Mount is the one that mounts power management. In this case, this PMIC chip can be sub-categorized as a Power Management Circuits chip. In total, IC powers are 3 pins on the board. Power managment ic pin count is 3. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 1V. There should be no more than 5.5V volts of supply voltage (Vsup) in this power management. Power management recommends the Surface Mount mounting type. Temperature setting for the supervisors should be -40°C~105°C TA. The output voltage of this power managment ic during operation is Push-Pull, Totem Pole. As far as the supply current of the power management is concerned, it is 9μA. It is always advisable to use MXD1810, the base supervisor number, when searching for similar PMICs from the manufacturer.
MXD1810UR41+T Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
9μA operating supply current
MXD1810UR41+T Applications
There are a lot of Maxim Integrated MXD1810UR41+T Voltage Supervisors applications.
- Digitally controlled LDO regulators circuit
- Urban rail transit weak current power monitoring
- Power distribution systems of operating room
- Insulation fault location system
- Set top box
- Radar
- Unattended substation automation
- DVR
- FPGA design
- DSP
