NC7SZ374P6X
| Parameters | |
|---|---|
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 1.65V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 1.8V |
| Base Part Number | 7SZ374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Number of Channels | 1 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 32mA |
| Number of Bits | 1 |
| Clock Frequency | 175MHz |
| Propagation Delay | 16.5 ns |
| Turn On Delay Time | 9.7 ns |
| Family | LVC/LCX/Z |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 1μA |
| Current - Output High, Low | 32mA 32mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 4ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 900μm |
| Length | 2mm |
| Width | 1.25mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Number of Pins | 6 |
| Weight | 28mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2004 |
| Series | 7SZ |
NC7SZ374P6X Overview
6-TSSOP, SC-88, SOT-363is the packaging method. You can find it in the Tape & Reel (TR)package. Currently, the output is configured to use Tri-State, Non-Inverted. Positive Edgeis the trigger it is configured with. There is an electric part mounted in the way of Surface Mount. A supply voltage of 1.65V~5.5V is required for operation. In this case, the operating temperature is -40°C~85°C TA. A flip flop of this type is classified as a D-Type. It belongs to the 7SZseries of FPGAs. A frequency of 175MHzshould not be exceeded by its output. It consumes 1μA of quiescent There are 6 terminations,It is a member of the 7SZ374 family. An input voltage of 1.8Vpowers the D latch. The input capacitance of this JK flip flopis 3pF farads. It is a member of the LVC/LCX/Zfamily of D flip flop. This electronic part is mounted in the way of Surface Mount. It is designed with 6 pins. The clock edge trigger type for this device is Positive Edge. This device has the base part number FF/Latches. There are 1bits in this flip flop. It reaches 5.5Vwhen the supply voltage is maximal (Vsup). This D flip flop is well suited for TAPE AND REEL based on its reliable performance. The D flip flop has no ports embedded. Featuring the maximum design flexibility, it has an output current of 32mA . The JK flip flop is with 3 output lines to operate. The number of channels is growing strong/weak: 1.
NC7SZ374P6X Features
Tape & Reel (TR) package
7SZ series
6 pins
1 Bits
NC7SZ374P6X Applications
There are a lot of ON Semiconductor NC7SZ374P6X Flip Flops applications.
- Single Up Count-Control Line
- Guaranteed simultaneous switching noise level
- Patented noise
- Balanced Propagation Delays
- Storage registers
- Functionally equivalent to the MC10/100EL29
- Memory
- Individual Asynchronous Resets
- Common Clocks
- Communications
