NC7WB66K8X
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-VFSOP (0.091, 2.30mm Width) |
| Number of Pins | 8 |
| Weight | 30mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Resistance | 13.5Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 250mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 2 |
| Supply Voltage | 2.3V |
| Terminal Pitch | 0.5mm |
| Base Part Number | NC7WB66 |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Power Dissipation | 250mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 10 ns |
| Supply Type | Single |
| Bandwidth | 300MHz |
| Turn-Off Delay Time | 10.5 ns |
| On-State Resistance (Max) | 10Ohm |
| High Level Output Current | 128mA |
| Low Level Output Current | 128mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 3.2ns, 4.1ns |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -70dB @ 10MHz |
| Switch-on Time-Max | 5.6ns |
| Switch-off Time-Max | 6.9ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Drain to Source Resistance | 6Ohm |
| Normal Position | NO |
| Height | 600μm |
| Length | 2mm |
| Width | 2.3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
NC7WB66K8X Overview
Packed in 8-VFSOP (0.091, 2.30mm Width), the electronic component is convenient for shipping overseas. The advanced packaging method Tape & Reel (TR) provides high reliability. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. 8 terminations have been made so far. This electronic part offers high-quality output due to its 2 channels. When the electronic component is given a voltage of 2.3V, it should be turned on and run. SPST - NO switching circuits are used in these analog switch ics. Try searching for NC7WB66 variants of the analog switch ic. The internal resistance of this digital multiplexer is 13.5Ohm. Please refer to the datasheets for 8 pins functions. A analogue multiplexer of this type is a Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. Single supply type digital switch with a low cost. The lowest voltage the electronic part should receive is 1.65V. Draining from a single voltage supply, this analog switch requires a voltage of 1.65V~5.5V. A digital multiplexer may suffer damage if voltage is applied above 1μA. There are various bandwidths available for data transfer. Resistivity from Drain to Source is 6Ohm for this electronic part.
NC7WB66K8X Features
2 Channels
Switch Circuit: SPST - NO
Bandwidth: 300MHz
Drain-to-Source resistance: 6Ohm
NC7WB66K8X Applications
There are a lot of ON Semiconductor NC7WB66K8X Analog Switches & Multiplexers ICs applications.
- Industrial
- Cell phones
- Audio signal routing
- Mechanical reed relay replacement
- Microprocessor controlled systems
- SONET
- Sample-and-hold systems
- Microprocessor Controlled Analog Systems
- Remote wireless modules
- Low-Voltage
