NCP1014AP100
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm), 7 Leads |
| Surface Mount | NO |
| Number of Pins | 7 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 7 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| HTS Code | 8542.39.00.01 |
| Subcategory | Switching Regulator or Controllers |
| Max Power Dissipation | 19W |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | NCP1014 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 10V |
| Input Voltage-Nom | 8V |
| Analog IC - Other Type | SWITCHING REGULATOR |
| Voltage - Supply (Vcc/Vdd) | 8.5V~10V |
| Topology | Flyback |
| Control Mode | CURRENT-MODE |
| Output Current-Max | 1A |
| Frequency - Switching | 100kHz |
| Control Technique | PULSE WIDTH MODULATION |
| Switcher Configuration | SINGLE |
| Internal Switch(s) | Yes |
| Fault Protection | Over Load, Over Temperature, Over Voltage |
| Max Duty Cycle | 72 % |
| Duty Cycle | 67% |
| Output Isolation | Isolated |
| Voltage - Breakdown | 700V |
| Height Seated (Max) | 4.45mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
NCP1014AP100 Overview
In the package 8-DIP (0.300, 7.62mm), 7 Leads , the ac to dc converter is embedded.It is available in Tube AC/DC power converter.As you can see, this AC/DC converter is mounted in the way of Through Hole .This ac dc converter should be operated at a temperature of -40°C~150°C TJ °C so that it can deliver its performance.Analog ICs of type SWITCHING REGULATOR are used in this AC DC converter.When the switching frequency reaches 100kHz , the circuit is closed.This AC/DC converter is designed for use within the range of 8.5V~10V supply voltage (Vcc/Vdd).In total, there are 7 terminations.The ac/dc converter has 7 pins.There are 8 pins on the ac-dc converter.If you select the NCP1014 family, you will be able to search similar acdc converters.Switching Regulator or Controllers contains the ac to dc conversions.A maximum current of 1A may be supplied to the ac to dc inverter.When the supply voltage is 10V , the interface IC conducts.
NCP1014AP100 Features
Packaged with 8-DIP (0.300, 7.62mm), 7 Leads
Switching Frequency at 100kHz
With 7 pins
Operating Supply Voltage at the range of 10V
NCP1014AP100 Applications
There are a lot of ON Semiconductor NCP1014AP100 AC DC Converters applications.
- Chargers for cell/cordless phones
- Battery chargers for smart phones
- Switching AC-DC Adapter
- Power tools fast chargers with trickle and on/off
- Humidifier
- Consumer electronics
- LED Driver
- Adapter for ADSL
- Battery chargers for cordless
- Small off-line low voltage power supplies
