NCP112PG
| Parameters | |
|---|---|
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | Multi-Voltage Supervisor |
| Terminal Finish | Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 1.25W |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | NCP112 |
| Output | Open Drain or Open Collector |
| Pin Count | 14 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 3mA |
| Power Dissipation | 1.25W |
| Adjustable Threshold | YES |
| Watchdog Timer | No |
| Reset | Active High |
| Voltage - Threshold | 3.3V 5V 12V Adj |
| Number of Voltages Monitored | 4 |
| Reset Timeout | Adjustable/Selectable |
| Supply Current-Max (Isup) | 5mA |
| Undervoltage Threshold | 10V |
| Overvoltage Threshold | 14.2V |
| Length | 18.86mm |
| Width | 7.62mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
NCP112PG Overview
As far as the mounting terminals of this voltage supervisor are concerned, it has 14 in total. A Tube package is used to package the power management. As a reference, this IC management includes 1 functions for your convenience. It is possible to find on this power management a series of 1 channels. To assist you, this PMIC includes 14-DIP (0.300, 7.62mm) functions. Compared to other Multi-Voltage Supervisor products, this PMIC has a lot of benefits to offer. During operation, the power ic is supplied with a voltage of 5V. There is a voltage supply of 4 for the PMIC chip, and the chip conducts at that voltage. The mount is attached to Through Hole. A IC power such as this can be classified as a Power Management Circuits power management system. In total, IC powers are 14 pins on the board. There are 14 pins on the power managment ic. It is recommended that Vsup should not be less than 4.5V for this IC power. There should be no more than 16V volts of maximum supply voltage (Vsup) in this power management. Power management recommends the Through Hole mounting type. You should set the supervisor's temperature during -40°C~125°C TA . Power management has an output of Open Drain or Open Collector during operation. In order to maintain a stable supply current for the power management, 3mA is the recommended value. A similar IC managements number of the manufacturer can always be found by using NCP112, the base power ics number. In order to operate this power management, it requires 5V volts of power.
NCP112PG Features
Multi-Voltage Supervisor type
Minimum supply voltage of 4.5V
3mA operating supply current
NCP112PG Applications
There are a lot of ON Semiconductor NCP112PG Voltage Supervisors applications.
- Magnetic resonance imaging
- Data storage applications
- Medical-specific isolation transformer
- Transformer load monitoring equipment
- Cloud computing
- Power communication system
- Rechargeable batteries
- Low voltage/high power - AI, GPU
- Automotive permanent magnet synchronous motors
- Detection of phase loss
