NCP1550SN18T1G
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-5 Thin, TSOT-23-5 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Additional Feature | PFM CONTROL TECHNIQUE IS ALSO POSSIBLE |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Frequency | 600kHz |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | NCP1550 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 1.8V |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 5V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 100mA |
| Voltage - Supply (Vcc/Vdd) | 2.45V~5.5V |
| Control Features | Enable |
| Topology | Buck |
| Control Mode | VOLTAGE-MODE |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | No |
| Switcher Configuration | SINGLE |
| Duty Cycle (Max) | 100% |
| Length | 3mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
NCP1550SN18T1G Overview
With a SOT-23-5 Thin, TSOT-23-5 package, the switching controller is suitable for a wide range of applications. For outputs of 1, this dc motor controller is suitable. Packaging for the pmic consists of Tape & Reel (TR) solid enclosures. Transistor Driver dc switching's outputs (s) can be handled by it. 2.45V~5.5V is the supply voltage and the operating voltage of the dc control. A -40°C~85°C TA dc switcher is not a problem. As it has a Surface Mount value, it can be used for general dc dc regulator. For efficient switching control, the dcdc regulator features Enable. The switch converters are connected to an analog IC with a SWITCHING CONTROLLER output. A switching converters's terminal (s) sits at the DUAL position. A variety of terminations with 5 of dc switching. It includes PULSE WIDTH MODULATION as one of the control techniques dc dc converter ic adapts. The DC switcher's nominal voltage is 5V. Search for "NCP1550" to find other relevant dc to dc converter ics. 5 pins are on switching converter. Specifically, switching converter falls under the Switching Regulator or Controllers category. Test statistics indicate DC regulator outputs 1.8V voltage. A starting point for a project is to note down the dc dc regulator's usual output current, which is 100mA. This Surface Mount makes DC switcher suitable for most prototypes and applications. A frequency of 600kHz is set for the switching controller. DC to DC voltage regulator has a value of PFM CONTROL TECHNIQUE IS ALSO POSSIBLE to better satisfy the need.
NCP1550SN18T1G Features
Transistor Driver Outputs
Enable
PULSE WIDTH MODULATION
Frequency: 600kHz
PFM CONTROL TECHNIQUE IS ALSO POSSIBLE
NCP1550SN18T1G Applications
There are a lot of ON Semiconductor NCP1550SN18T1G DC to DC converter applications.
- Access control systems
- Lathes
- Smart grid
- Domestic water pumps
- Experimental setup
- Servo drive system
- Fire elevators
- Flaw detection equipment
- Serial communication converter
- Laboratories
