NCP303LSN16T1
| Parameters | |
|---|---|
| Lifecycle Status | OBSOLETE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-5 Thin, TSOT-23-5 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Tin/Lead (Sn80Pb20) |
| Subcategory | Power Management Circuits |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 1.5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | NCP303 |
| Output | Open Drain or Open Collector |
| Pin Count | 5 |
| Number of Channels | 1 |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 800mV |
| Operating Supply Current | 500nA |
| Nominal Supply Current | 450nA |
| Adjustable Threshold | NO |
| Accuracy | 2 % |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 1.6V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | Adjustable/Selectable |
| Threshold Voltage | +1.6V |
| Undervoltage Threshold | 1.568V |
| Overvoltage Threshold | 1.632V |
| Length | 3mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
NCP303LSN16T1 Overview
It is mounted through 5 terminals on the power management. In terms of packaging, power management follows the Tape & Reel (TR) model. Please refer to this PMIC for 1 functions. This power managment ic consists of 1 channels, each of which can be used independently. There are SOT-23-5 Thin, TSOT-23-5 functions included in this PMIC so that you can refer to them. There are a lot of similarities between this IC management and other Simple Reset/Power-On Reset products. In order to ensure a good reflow performance, the package peak reflow temperature must be set at 240. The supervisor is always powered by a 1.5V volt supply. Power ics operate at 1 supply voltages. The mount is attached to Surface Mount. The power management system can be categorized as a Power Management Circuits chip. It has a total of 5 pins that are attached to IC management. Power managment ic pin count is 5. I should note that the minimum supply voltage (Vsup) for this IC management should be at least 800mV, which is the minimum supply voltage that should be applied. There should be no more than 10V volts of maximum supply voltage (Vsup) in this power management. The recommended mounting type is Surface Mount. This power management is the recommended temperature range for the supervisors: -40°C~125°C TA. As a result of this supervisor's operation, the output voltage is Open Drain or Open Collector. It is estimated that the voltage supervisor's supply current is 500nA. A similar IC managements number of the manufacturer can always be found by using NCP303, the base power ics number.
NCP303LSN16T1 Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 800mV
500nA operating supply current
NCP303LSN16T1 Applications
There are a lot of ON Semiconductor NCP303LSN16T1 Voltage Supervisors applications.
- Military electronics
- Stable power system
- Insulation fault location system
- Rechargeable batteries
- DSP
- Household appliances
- Computer applications
- Leakage protection
- Power distribution systems of CCU
- Dash board
