banner_page

NCP380HSN10AAT1G

P-Channel PMIC NCP380 5 Pin 5V SOT-23-5 Thin, TSOT-23-5


  • Manufacturer: ON Semiconductor
  • Nocochips NO: 598-NCP380HSN10AAT1G
  • Package: SOT-23-5 Thin, TSOT-23-5
  • Datasheet: PDF
  • Stock: 225
  • Description: P-Channel PMIC NCP380 5 Pin 5V SOT-23-5 Thin, TSOT-23-5 (Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Lifecycle Status ACTIVE (Last Updated: 4 days ago)
Mount Surface Mount
Mounting Type Surface Mount
Package / Case SOT-23-5 Thin, TSOT-23-5
Number of Pins 5
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2009
JESD-609 Code e3
Feature Slew Rate Controlled, Status Flag
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 5
ECCN Code EAR99
Resistance 135mOhm
Terminal Finish Tin (Sn)
Max Power Dissipation 325mW
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) NOT SPECIFIED
Number of Functions 1
Supply Voltage 5V
Current Rating 1A
Time@Peak Reflow Temperature-Max (s) NOT SPECIFIED
Base Part Number NCP380
Pin Count 5
Number of Outputs 1
Output Type P-Channel
Max Output Current 1A
Operating Supply Voltage 5.5V
Number of Channels 1
Interface On/Off
Analog IC - Other Type POWER SUPPLY SUPPORT CIRCUIT
Output Configuration High Side
Output Current 1A
Voltage - Supply (Vcc/Vdd) Not Required
Adjustable Threshold NO
Input Type Non-Inverting
Turn On Delay Time 4 ms
Switch Type General Purpose
Min Input Voltage 2.5V
Number of Inputs 2
Max Input Voltage 5.5V
Halogen Free Halogen Free
Nominal Input Voltage 5.5V
Turn-Off Delay Time 3 ms
Ratio - Input:Output 1:1
Voltage - Load 2.5V~5.5V
Fault Protection Current Limiting (Fixed), UVLO
Rds On (Typ) 70m Ω
Height 1mm
Length 3mm
Width 1.5mm
REACH SVHC No SVHC
RoHS Status ROHS3 Compliant
Lead Free Lead Free

NCP380HSN10AAT1G Overview


A Tape & Reel (TR) is used to package it.There is a package for it in the SOT-23-5 Thin, TSOT-23-5 package.The mounting type of the LED driver is Surface Mount.It owns the General Purpose switch type.To ensure reliable performance, the temperature should be set to -40°C~85°C TA.In this LED driver, there are no outputs available.Operation is based on Not Required supply voltage.There is a maximum output voltage of P-Channel volts.A lighting driver with Slew Rate Controlled, Status Flag features is available.It is part of the NCP380 family of LED drivers.As a result, there are 5 terminations.For operation, we use the 5 pins.As far as functions are concerned, the lighting driver has 1.To meet the operation criteria, the maximum output current drops to 1A.A supply voltage of 5V leads to high efficiency.Surface Mount is mounted in the way of this LED driving board.A total of 5 pins are present on it.135mOhm resistance is present in the lighting driver.This case results in a 1A output current.The analog IC used in this lighting driver is POWER SUPPLY SUPPORT CIRCUIT.In total, there are 1 channels available.When using this LED driving board, it is recommended that the supply voltage is set to 5.5V.It has a maximum input voltage of 5.5V volts.It has a 2.5V volt minimum input voltage.There are 2 inputs available.

NCP380HSN10AAT1G Features


Supplied from 5V
Resistance of 135mOhm
1 channels

NCP380HSN10AAT1G Applications


There are a lot of ON Semiconductor NCP380HSN10AAT1G Power Switches ICs applications.

  • Hot-Swap Systems
  • Gaming
  • Hard Disk Drives
  • Notebook and Tablet Computers
  • Hot Swaps
  • Various applications equipped with buttons
  • Portable GPS Device
  • Smart Phones, Feature Phones
  • Hot Swap
  • Set-Top Boxes

Write a review

Note: HTML is not translated!
    Bad           Good