NCP382HD10AAR2G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Feature | Slew Rate Controlled, Status Flag |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 140mOhm |
| Terminal Finish | Tin (Sn) |
| Max Power Dissipation | 570mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Current Rating | 1A |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | NCP382 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Output Type | P-Channel |
| Operating Supply Voltage | 5.5V |
| Number of Channels | 2 |
| Interface | On/Off |
| Analog IC - Other Type | POWER SUPPLY SUPPORT CIRCUIT |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Adjustable Threshold | NO |
| Input Type | Non-Inverting |
| Turn On Delay Time | 3 ms |
| Switch Type | General Purpose |
| Min Input Voltage | 2.5V |
| Number of Inputs | 3 |
| Max Input Voltage | 5.5V |
| Halogen Free | Halogen Free |
| Turn-Off Delay Time | 3 ms |
| Ratio - Input:Output | 1:2 |
| Voltage - Load | 2.5V~5.5V |
| Fault Protection | Current Limiting (Fixed), Over Temperature, UVLO |
| Rds On (Typ) | 80m Ω |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
NCP382HD10AAR2G Overview
A Tape & Reel (TR) is used to package it.It is included with the 8-SOIC (0.154, 3.90mm Width) package as well.This LED driving board is mounted using the mounting type Surface Mount.General Purpose is the switch type it owns.To ensure reliable operation, set the temperature to -40°C~85°C TA.In this LED driver, there are no outputs available.The LED driving board is powered by a voltage of Not Required.A maximum output voltage of P-Channel volts can be obtained with this LED driver.There are Slew Rate Controlled, Status Flag features available on the LED driving board.It is part of the NCP382 family of LED drivers.A total of 8 terminations can be found in it.In order to operate, the 8 pins are used.As far as the lighting driver is concerned, there are 1 functions.With a supply voltage of 5V, high efficiency is possible.The lighting driver is mounted in the direction of Surface Mount.The LED driver has a total of 8 pins.It has a resistance of 140mOhm.The gadget uses an analog IC, which is POWER SUPPLY SUPPORT CIRCUIT in this case.A total of 2 channels are available for you to choose from.The supply voltage should be set at 5.5V for best efficiency.The maximum input voltage is 5.5V volts.Input voltage must be at least 2.5V volts.With 3 inputs, it is equipped.
NCP382HD10AAR2G Features
Supplied from 5V
Resistance of 140mOhm
2 channels
NCP382HD10AAR2G Applications
There are a lot of ON Semiconductor NCP382HD10AAR2G Power Switches ICs applications.
- USB Power Distribution
- PC Card Hot Swap
- USB Ports/Hubs
- Notebook and Tablet Computers
- Solid-State Drives
- Wireless/Networking Cards
- Telecom and Network Systems
- HDD and SSD
- Storage Drives
- Hard Disk Drives
