NCP383LMUAJAATXG
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-UFDFN Exposed Pad |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| JESD-609 Code | e3 |
| Feature | Slew Rate Controlled, Status Flag |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 95mOhm |
| Terminal Finish | Tin (Sn) |
| Max Power Dissipation | 850mW |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 10 |
| Number of Outputs | 2 |
| Output Type | N-Channel |
| Max Output Current | 2.5A |
| Operating Supply Voltage | 5.5V |
| Interface | On/Off |
| Analog IC - Other Type | SPST |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 1μA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 9 ms |
| Switch Type | General Purpose |
| Min Input Voltage | 2.7V |
| Max Input Voltage | 5.5V |
| Halogen Free | Halogen Free |
| Nominal Input Voltage | 5.5V |
| Turn-Off Delay Time | 3 ms |
| Ratio - Input:Output | 1:2 |
| Voltage - Load | 2.7V~5.5V |
| Fault Protection | Current Limiting (Adjustable), Over Temperature, UVLO |
| Rds On (Typ) | 45m Ω |
| Height | 500μm |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
NCP383LMUAJAATXG Overview
As a result, it is packaged in the form of a Tape & Reel (TR).Package 10-UFDFN Exposed Pad contains it.The mounting type of the LED driver is Surface Mount.There is a General Purpose switch type associated with it.It is recommended to set the temperature to -40°C~85°C TA in order to ensure reliable operation.It is possible to use 2 outputs in the lighting driver.To operate, it needs a supply voltage of Not Required.A maximum output voltage of N-Channel volts can be obtained with this LED driver.In terms of features, the LED driving board has Slew Rate Controlled, Status Flag.The 10 pins are used to operate the LED driver.The maximum output current is reduced to 2.5A to meet the operation criteria.It is positioned in the direction of Surface Mount.A total of 10 pins are included in this LED driver.In this LED driving board, there is 95mOhm resistance.There is an analog input IC in this gadget, which is SPST.For maximum efficiency, the supply voltage should be set to 5.5V.There is a maximum input voltage of 5.5V volts.There is a minimum input voltage of 2.7V volts for this LED driver.A maximum current requirement of 1μA is required for its operation.
NCP383LMUAJAATXG Features
Resistance of 95mOhm
NCP383LMUAJAATXG Applications
There are a lot of ON Semiconductor NCP383LMUAJAATXG Power Switches ICs applications.
- Hot-Swap Systems
- USB Ports/Hubs
- Notebook PC
- Portable Devices
- Telecom and Network Systems
- Smart Phones, Feature Phones
- Wireless Modem Data Cards
- Portable Music Players
- Hard Disk Drives
- PDAs
