NCS2001SQ2T2G
| Parameters | |
|---|---|
| Halogen Free | Halogen Free |
| Output Current per Channel | 96mA |
| Input Offset Voltage (Vos) | 6mV |
| Bandwidth | 1.4MHz |
| Neg Supply Voltage-Nom (Vsup) | -2.5V |
| Unity Gain BW-Nom | 1400 kHz |
| Voltage Gain | 92.04dB |
| Power Supply Rejection Ratio (PSRR) | 55dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 500μV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Height | 1mm |
| Length | 2.2mm |
| Width | 1.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 11 hours ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~105°C |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Max Power Dissipation | 286mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | NC*2001 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Operating Supply Current | 820μA |
| Nominal Supply Current | 820μA |
| Power Dissipation | 286mW |
| Output Current | 76mA |
| Slew Rate | 1.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 10pA |
| Voltage - Supply, Single/Dual (±) | 0.9V~7V ±0.45V~3.5V |
NCS2001SQ2T2G Overview
In order to protect the op amps, a 5-TSSOP, SC-70-5, SOT-353 case is used. There are two types of operational amplifiers in this circuit. It comes in a Tape & Reel (TR) case, which protects instrumentation amplifier from damage during delivery. There have been a total of 5 terminations over the past year. Linear amplifier has a total of 5 pins. Please take in mind that op amp should be run at 2.5V. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. 5 pins are located on the operational amplifiers. Op amp rates 6mV as input offset voltage. Surface Mount is the recommended mounting type of operational amplifiers. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~105°C. As long as the supply current of the chip does not exceed 820μA, this op amp ic can operate. You should keep the voltage gain at 92.04dB for the time being. As far as the device is concerned, buffer amplifier has 1 channels. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. The instrumentation amplifier is packed in the form of TAPE AND REEL.
NCS2001SQ2T2G Features
5 Pins
supply voltage of 2.5V
92.04dB voltage gain
Output Type: Rail-to-Rail
NCS2001SQ2T2G Applications
There are a lot of ON Semiconductor NCS2001SQ2T2G Instrumentational OP Amps applications.
- High gain DC amplifier
- Displayers for aircraft and air transportation control systems
- RF cable systems
- Integrator circuits
- High-frequency data acquisition systems
- MP3
- Signal operation
- Car stereo
- Polarized electrodes
- Band-stop filter
