NCS2372DWR2G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Number of Channels | 2 |
| Number of Circuits | 1 |
| Max Supply Voltage | 40V |
| Operating Supply Current | 8mA |
| Nominal Supply Current | 8mA |
| Output Current | 1A |
| Slew Rate | 1.4V/μs |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 100nA |
| Halogen Free | Halogen Free |
| Output Current per Channel | 1A |
| Input Offset Voltage (Vos) | 1mV |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1400 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.5μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Max Dual Supply Voltage | 20V |
| Max Frequency | 100kHz |
| Min Dual Supply Voltage | 2.5V |
| Nominal Gain Bandwidth Product | 1.4MHz |
| Height | 2.4mm |
| Length | 10.45mm |
| Width | 7.6mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
NCS2372DWR2G Overview
In order to protect the op amps, a 16-SOIC (0.295, 7.50mm Width) case is used. There are two types of operational amplifiers in this circuit. It comes in a Tape & Reel (TR) case, which protects instrumentation amplifier from damage during delivery. The number of terminations is approaching the 16 mark. Buffer amplifier has a total of 16 pins on it. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. It should be noted that this op amp is a type of Operational Amplifier device. In total, the buffer amplifier consists of 16 pins. Op amp rates 1mV as input offset voltage. Surface Mount is the recommended mounting type of operational amplifiers. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~125°C . An 8mA volt supply current is needed for this linear amplifier to operate. Maintain 100dB as the voltage gain. There are 1 circuits on this op amp. There are a total of 2 channels available on the op amps. The operating supply voltage of instrumentation amplifier is rated 20V voltage. This electric component can work from a voltage of under 40V as far as supply voltage is concerned. In order for this electronic part to be conducted successfully, you should use a dual supply voltage of 20V.
NCS2372DWR2G Features
16 Pins
supply voltage of 15V
100dB voltage gain
NCS2372DWR2G Applications
There are a lot of ON Semiconductor NCS2372DWR2G Instrumentational OP Amps applications.
- Portable media players
- Automation control systems
- Ultrasound transducers
- Test and measurement instruments
- Instrumentation
- PDA
- Car stereo
- Micro signal measurement
- Measurements of Wheatstone bridge
- E-book readers
