NCV2001SN2T1G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-5 Thin, TSOT-23-5 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Max Power Dissipation | 340mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | NC*2001 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Number of Elements | 1 |
| Operating Supply Current | 820μA |
| Nominal Supply Current | 1.5mA |
| Power Dissipation | 340mW |
| Output Current | 76mA |
| Slew Rate | 1.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 10pA |
| Voltage - Supply, Single/Dual (±) | 0.9V~7V ±0.45V~3.5V |
| Halogen Free | Halogen Free |
| Output Current per Channel | 96mA |
| Input Offset Voltage (Vos) | 6mV |
| Bandwidth | 1.4MHz |
| Neg Supply Voltage-Nom (Vsup) | -2.5V |
| Unity Gain BW-Nom | 1400 kHz |
| Voltage Gain | 92.04dB |
| Power Supply Rejection Ratio (PSRR) | 55dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 500μV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Height | 1mm |
| Length | 3mm |
| Width | 1.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
NCV2001SN2T1G Overview
There is a SOT-23-5 Thin, TSOT-23-5 case in which the instrumentation amplifier is packaged. The instrumentation amplifier in this picture is of the General Purpose-type. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. In recent months, the number of terminations has approached 5. There are a total of 5 pins on this op amp. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 2.5V. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. There are 5 pins on this chip. Regarding input offset voltage, op amp rates 6mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~125°C. Using an 820μA supply current, this operational amplifier ics can be operated. There should be no change in the voltage gain at 92.04dB. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. As a whole, there are 1 elements that make up this buffer amplifier. It is used TAPE AND REEL to pack the op amps. Instrumentation amplifiers are numbered by their Automotive, AEC-Q100 series.
NCV2001SN2T1G Features
5 Pins
supply voltage of 2.5V
92.04dB voltage gain
Output Type: Rail-to-Rail
NCV2001SN2T1G Applications
There are a lot of ON Semiconductor NCV2001SN2T1G Instrumentational OP Amps applications.
- High input resistance broadband
- Image computer boards
- High-frequency data acquisition systems
- Multiplication circuits
- Vehicle electronics
- Proportional counter tubes
- Test and measurement instruments
- Signal filtering
- Cinema or auditorium audio system
- single/dual op amp sum and difference circuits
