NCV2904DR2G
| Parameters | |
|---|---|
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | NCV2904 |
| Pin Count | 8 |
| Operating Supply Voltage | 16V |
| Number of Channels | 2 |
| Operating Supply Current | 1.5mA |
| Nominal Supply Current | 1.2mA |
| Output Current | 40mA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 45nA |
| Voltage - Supply, Single/Dual (±) | 3V~32V ±1.5V~16V |
| Halogen Free | Halogen Free |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 7mV |
| Bandwidth | 1MHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.5μA |
| Power Supply Rejection Ratio (PSRR) | 50dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 2mV |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
NCV2904DR2G Overview
There is a 8-SOIC (0.154, 3.90mm Width) case package that contains the instrumentation amplifiers. This is a General Purpose type op amp. It comes in a Tape & Reel (TR) case, which protects instrumentation amplifier from damage during delivery. It is estimated that there will be at least 8 terminations this year. A total of 8 pins are located on this board. This linear amplifier should be powered by an 5V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. 8 pins are located on the operational amplifiers. There is an input offset voltage of 7mV for this buffer op amp. For this electronic part, it is recommended that you mount it with type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. As long as the supply current of the chip does not exceed 1.5mA, this op amp ic can operate. 100dB should be the voltage gain. On the buffer amps, there are 2 channels that can be used. The operating supply voltage of the buffer op amp is rated at 16V. As a result of this, the buffer amplifier is packed in TAPE AND REEL. This buffer amplifier is assigned within the Automotive, AEC-Q100 series by its manufacturer.
NCV2904DR2G Features
8 Pins
supply voltage of 5V
100dB voltage gain
NCV2904DR2G Applications
There are a lot of ON Semiconductor NCV2904DR2G Instrumentational OP Amps applications.
- single/dual op amp sum and difference circuits
- Differentiator circuits
- Subtraction operation circuits
- Blood pressure sensors
- Thermocouples
- Large motor controllers
- Switching amplifier
- Automotive sensors
- Test equipment
- Television
