NCV887101D1R2G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Base Part Number | NCV887101 |
| Function | Step-Up, Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Type | Transistor Driver |
| Max Output Current | 100μA |
| Operating Supply Voltage | 40V |
| Input Voltage-Nom | 13.2V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 575mA |
| Voltage - Supply (Vcc/Vdd) | 3.2V~40V |
| Control Features | Current Limit, Enable |
| Max Output Voltage | 2.5V |
| Topology | Boost, Flyback |
| Min Input Voltage | 3.2V |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 1MHz |
| Max Input Voltage | 40V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | No |
| Min Output Voltage | 300mV |
| Max Frequency | 1.1MHz |
| Duty Cycle (Max) | 86% |
| Clock Sync | Yes |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
NCV887101D1R2G Overview
This switching controller fits most application requirements since it is packaged in a 8-SOIC (0.154, 3.90mm Width) package. There is sufficient capacity to generate switching controller for outputs 1. The pmic is packaged in Tape & Reel (TR) solid enclosure. Transistor Driver dc switching's outputs (s) are supported. dc control's supply and operating voltages are 3.2V~40V. Worked in a -40°C~150°C TJ dc switcher before. There is a switch at 1MHz that can be used with this controller. It is suitable for general dc dc regulator when it is set to Surface Mount. Current Limit, Enable is used for efficient switching control in the dcdc regulator. The switch converters are connected to an analog IC with a SWITCHING CONTROLLER output. switching converters terminal (s) are designed to be at DUAL. A variety of dc switching's functions can be performed on 8 terminations. Some of the control techniques used by these dc dc converter ics are PULSE WIDTH MODULATION. It is inputted with a DC switcher's voltage of 13.2V. You can find other relevant dc to dc converter ics by searching "NCV887101". There are 8 pins on switching converter. Specially, switching converter corresponds to type Switching Regulator or Controllers. normally, the dc dc regulator's output current is 575mA, which you should keep in mind when starting a project. Having a Surface Mount makes DC switcher ideal for most prototype and application designs. DC regulator's maximum frequency is 1.1MHz. In order to run the voltage regulator dc to dc safely and reliably, users are advised to apply 40V. Users must limit the voltage accordingly because the dc switcher's maximum input voltage is 40V. A voltage of 3.2V must be present in the supply. The dc switcher will not provide an output current greater than 100μA. The switching converter can output 2.5V volts at its utmost, according to the datasheet. 300mV voltage output is lower than 300mV.
NCV887101D1R2G Features
Transistor Driver Outputs
Switching Frequency: 1MHz
Current Limit, Enable
PULSE WIDTH MODULATION
NCV887101D1R2G Applications
There are a lot of ON Semiconductor NCV887101D1R2G DC to DC converter applications.
- Computed tomography (CT)
- Hydrogen power
- Automatic plug-in machines
- Network technology
- Packaging
- Mobile phones
- Electrical distribution systems
- Electrical power transmission
- Sink circuits
- Servo drive system
